Speed Passion F1 car - The SP1
#556
Tech Elite
iTrader: (36)
If you look in the sidebar of the manual, they mention 1x2mm or 2x2mm shims under the lower arms. They describe it in terms of 200mm and 190mm widths respectively, though, which I don't fully understand either.
So much to learn
#557
Tech Elite
iTrader: (36)
Ok, one more late night question/observation. I've read a lot of discussion about the front 190mm setting being 2mm too wide when running Shimizu tires, hence a lot of crazy modifications. So, according to this chart, you get 190mm by using both "outside" holes, with the notches pointing out: http://www.petitrc.com/reglages/spee...F1_Trackwidth/
However, I used that outside holes and pointed the notches inward, which narrowed the width by almost 2mm. So, the 190mm setting, but with notches pointing inward the chassis.
So... am I crazy? What's wrong with my idea? Won't this give me very close to 190mm with Shimizu tires?
However, I used that outside holes and pointed the notches inward, which narrowed the width by almost 2mm. So, the 190mm setting, but with notches pointing inward the chassis.
So... am I crazy? What's wrong with my idea? Won't this give me very close to 190mm with Shimizu tires?
#558
Tech Champion
Yes I raised the servo mounts as well but the servo I did not raise.
#559
In that case you also had to raise the servo mounts, correct?
If you look in the sidebar of the manual, they mention 1x2mm or 2x2mm shims under the lower arms. They describe it in terms of 200mm and 190mm widths respectively, though, which I don't fully understand either.
So much to learn
If you look in the sidebar of the manual, they mention 1x2mm or 2x2mm shims under the lower arms. They describe it in terms of 200mm and 190mm widths respectively, though, which I don't fully understand either.
So much to learn
#560
Tech Elite
iTrader: (2)
Nothing I did the same on mine to narrow the front up a touch
Ok, one more late night question/observation. I've read a lot of discussion about the front 190mm setting being 2mm too wide when running Shimizu tires, hence a lot of crazy modifications. So, according to this chart, you get 190mm by using both "outside" holes, with the notches pointing out: http://www.petitrc.com/reglages/spee...F1_Trackwidth/
However, I used that outside holes and pointed the notches inward, which narrowed the width by almost 2mm. So, the 190mm setting, but with notches pointing inward the chassis.
So... am I crazy? What's wrong with my idea? Won't this give me very close to 190mm with Shimizu tires?
However, I used that outside holes and pointed the notches inward, which narrowed the width by almost 2mm. So, the 190mm setting, but with notches pointing inward the chassis.
So... am I crazy? What's wrong with my idea? Won't this give me very close to 190mm with Shimizu tires?
#561
Tech Elite
iTrader: (36)
I see the site is back! So... I basically finished by kit build. I have two questions:
1. Are you guys seeing a lot of play in your shock around the two mounting ball studs? I know the shock goes in "upside down" due to the different size balls (4.7 and 4.3 if I recall), and will only mount one way. But.. even then, there is play around the balls. I know the idea is to not bind the shock, but it seems rather sloppy.
2. For those of you running shorty packs, are you running it fully forward, fully in the back, or somewhere in between? I have room to mount my ESC inline and I'm trying to decide where to put it. I'm thinking battery all the way forward, but that means removing both pieces of the upper deck to get it in there (not a huge problem). From what I've read, most F1s run it fully forward, but I wanted to check.
3. If I do run the ESC in the back, am I at all worried about the tweak the wires may introduce on the back pod? I'd be using 14ga wires, but they're still stiff enough to "press" down on the motor. I'm thinking of running them over the top of the rear shock brace.
Thanks!
1. Are you guys seeing a lot of play in your shock around the two mounting ball studs? I know the shock goes in "upside down" due to the different size balls (4.7 and 4.3 if I recall), and will only mount one way. But.. even then, there is play around the balls. I know the idea is to not bind the shock, but it seems rather sloppy.
2. For those of you running shorty packs, are you running it fully forward, fully in the back, or somewhere in between? I have room to mount my ESC inline and I'm trying to decide where to put it. I'm thinking battery all the way forward, but that means removing both pieces of the upper deck to get it in there (not a huge problem). From what I've read, most F1s run it fully forward, but I wanted to check.
3. If I do run the ESC in the back, am I at all worried about the tweak the wires may introduce on the back pod? I'd be using 14ga wires, but they're still stiff enough to "press" down on the motor. I'm thinking of running them over the top of the rear shock brace.
Thanks!
#562
Tech Champion
iTrader: (22)
Hey guys, i am not sure if this was already posted
http://rcf1blog.blogspot.ca/2013/07/...sion-sp-1.html
What does moving the links at an angle do to make it "feel more planted"?
http://rcf1blog.blogspot.ca/2013/07/...sion-sp-1.html
What does moving the links at an angle do to make it "feel more planted"?
#563
Tech Champion
I see the site is back! So... I basically finished by kit build. I have two questions:
1. Are you guys seeing a lot of play in your shock around the two mounting ball studs? I know the shock goes in "upside down" due to the different size balls (4.7 and 4.3 if I recall), and will only mount one way. But.. even then, there is play around the balls. I know the idea is to not bind the shock, but it seems rather sloppy.
2. For those of you running shorty packs, are you running it fully forward, fully in the back, or somewhere in between? I have room to mount my ESC inline and I'm trying to decide where to put it. I'm thinking battery all the way forward, but that means removing both pieces of the upper deck to get it in there (not a huge problem). From what I've read, most F1s run it fully forward, but I wanted to check.
3. If I do run the ESC in the back, am I at all worried about the tweak the wires may introduce on the back pod? I'd be using 14ga wires, but they're still stiff enough to "press" down on the motor. I'm thinking of running them over the top of the rear shock brace.
Thanks!
1. Are you guys seeing a lot of play in your shock around the two mounting ball studs? I know the shock goes in "upside down" due to the different size balls (4.7 and 4.3 if I recall), and will only mount one way. But.. even then, there is play around the balls. I know the idea is to not bind the shock, but it seems rather sloppy.
2. For those of you running shorty packs, are you running it fully forward, fully in the back, or somewhere in between? I have room to mount my ESC inline and I'm trying to decide where to put it. I'm thinking battery all the way forward, but that means removing both pieces of the upper deck to get it in there (not a huge problem). From what I've read, most F1s run it fully forward, but I wanted to check.
3. If I do run the ESC in the back, am I at all worried about the tweak the wires may introduce on the back pod? I'd be using 14ga wires, but they're still stiff enough to "press" down on the motor. I'm thinking of running them over the top of the rear shock brace.
Thanks!
2. I run mine fully forward with the ESC in the back.
3. Use 16awg wire. Unless your running some really hot motor you don't need more than 16awg.
#564
Tech Champion
iTrader: (42)
I see the site is back! So... I basically finished by kit build. I have two questions:
1. Are you guys seeing a lot of play in your shock around the two mounting ball studs? I know the shock goes in "upside down" due to the different size balls (4.7 and 4.3 if I recall), and will only mount one way. But.. even then, there is play around the balls. I know the idea is to not bind the shock, but it seems rather sloppy.
2. For those of you running shorty packs, are you running it fully forward, fully in the back, or somewhere in between? I have room to mount my ESC inline and I'm trying to decide where to put it. I'm thinking battery all the way forward, but that means removing both pieces of the upper deck to get it in there (not a huge problem). From what I've read, most F1s run it fully forward, but I wanted to check.
3. If I do run the ESC in the back, am I at all worried about the tweak the wires may introduce on the back pod? I'd be using 14ga wires, but they're still stiff enough to "press" down on the motor. I'm thinking of running them over the top of the rear shock brace.
Thanks!
1. Are you guys seeing a lot of play in your shock around the two mounting ball studs? I know the shock goes in "upside down" due to the different size balls (4.7 and 4.3 if I recall), and will only mount one way. But.. even then, there is play around the balls. I know the idea is to not bind the shock, but it seems rather sloppy.
2. For those of you running shorty packs, are you running it fully forward, fully in the back, or somewhere in between? I have room to mount my ESC inline and I'm trying to decide where to put it. I'm thinking battery all the way forward, but that means removing both pieces of the upper deck to get it in there (not a huge problem). From what I've read, most F1s run it fully forward, but I wanted to check.
3. If I do run the ESC in the back, am I at all worried about the tweak the wires may introduce on the back pod? I'd be using 14ga wires, but they're still stiff enough to "press" down on the motor. I'm thinking of running them over the top of the rear shock brace.
Thanks!
2. Fully forward w/ ESC behind.
3. I run this way and have no issues.
#566
Tech Elite
iTrader: (36)
Ok, time for me to start giving back to this thread. Two build tips for those of you who are thinking of getting this kit:
1. A lot of people are having trouble with the lock nuts that hold the "football" to the chassis, as they want to spin inside their soft plastic slots. I took a pretty easy approach to this: hold the lock nut in place (from spinning) with smooth needle nose pliers. If the lock nut is up against one side, squeeze it gently into the plastic with one side of the pliers, the other side resting on the outside of the football. If the lock nut is more in the middle, then just hold the flat sides with pliers. Since you don't tighten those too much, not much force is needed.
2. The first step has you assemble the pivot balls. As has been described here, they aren't properly finished and have metal flashing left behind. Some dremel it out, some force it, I was unable to do either. So, just save yourself the headache and order a set of these: https://www.tqrcracing.com/shop/prod....asp?p_id=2020 They are a direct fit and bolt right up with the kit hardware. They're also finished really nicely and well worth the price.
I'll have more once I try the car out on carpet and verify some of my other ideas
1. A lot of people are having trouble with the lock nuts that hold the "football" to the chassis, as they want to spin inside their soft plastic slots. I took a pretty easy approach to this: hold the lock nut in place (from spinning) with smooth needle nose pliers. If the lock nut is up against one side, squeeze it gently into the plastic with one side of the pliers, the other side resting on the outside of the football. If the lock nut is more in the middle, then just hold the flat sides with pliers. Since you don't tighten those too much, not much force is needed.
2. The first step has you assemble the pivot balls. As has been described here, they aren't properly finished and have metal flashing left behind. Some dremel it out, some force it, I was unable to do either. So, just save yourself the headache and order a set of these: https://www.tqrcracing.com/shop/prod....asp?p_id=2020 They are a direct fit and bolt right up with the kit hardware. They're also finished really nicely and well worth the price.
I'll have more once I try the car out on carpet and verify some of my other ideas
#567
Ok, time for me to start giving back to this thread. Two build tips for those of you who are thinking of getting this kit:
1. A lot of people are having trouble with the lock nuts that hold the "football" to the chassis, as they want to spin inside their soft plastic slots. I took a pretty easy approach to this: hold the lock nut in place (from spinning) with smooth needle nose pliers. If the lock nut is up against one side, squeeze it gently into the plastic with one side of the pliers, the other side resting on the outside of the football. If the lock nut is more in the middle, then just hold the flat sides with pliers. Since you don't tighten those too much, not much force is needed.
2. The first step has you assemble the pivot balls. As has been described here, they aren't properly finished and have metal flashing left behind. Some dremel it out, some force it, I was unable to do either. So, just save yourself the headache and order a set of these: https://www.tqrcracing.com/shop/prod....asp?p_id=2020 They are a direct fit and bolt right up with the kit hardware. They're also finished really nicely and well worth the price.
I'll have more once I try the car out on carpet and verify some of my other ideas
1. A lot of people are having trouble with the lock nuts that hold the "football" to the chassis, as they want to spin inside their soft plastic slots. I took a pretty easy approach to this: hold the lock nut in place (from spinning) with smooth needle nose pliers. If the lock nut is up against one side, squeeze it gently into the plastic with one side of the pliers, the other side resting on the outside of the football. If the lock nut is more in the middle, then just hold the flat sides with pliers. Since you don't tighten those too much, not much force is needed.
2. The first step has you assemble the pivot balls. As has been described here, they aren't properly finished and have metal flashing left behind. Some dremel it out, some force it, I was unable to do either. So, just save yourself the headache and order a set of these: https://www.tqrcracing.com/shop/prod....asp?p_id=2020 They are a direct fit and bolt right up with the kit hardware. They're also finished really nicely and well worth the price.
I'll have more once I try the car out on carpet and verify some of my other ideas
#568
Tech Elite
iTrader: (36)
My current issue: fitting the McLaren body to the chassis. Cut out per the mold lines, it almost fits, but hits in several places. My biggest point of confusion is whether or not I'm meant to keep the "tail" of the body, the part that swoops down over the motor, behind the air intake. If I am, soldering wires back there will be super tight, and there is no way I can run a heat sink. I may just wait till Saturday and see what others have done before I start cutting.
#569
Tech Initiate
No problem! This build has been slower than most as all this is new to me. Never had a pan car, so a lot about this car took me a while to figure out.
My current issue: fitting the McLaren body to the chassis. Cut out per the mold lines, it almost fits, but hits in several places. My biggest point of confusion is whether or not I'm meant to keep the "tail" of the body, the part that swoops down over the motor, behind the air intake. If I am, soldering wires back there will be super tight, and there is no way I can run a heat sink. I may just wait till Saturday and see what others have done before I start cutting.
My current issue: fitting the McLaren body to the chassis. Cut out per the mold lines, it almost fits, but hits in several places. My biggest point of confusion is whether or not I'm meant to keep the "tail" of the body, the part that swoops down over the motor, behind the air intake. If I am, soldering wires back there will be super tight, and there is no way I can run a heat sink. I may just wait till Saturday and see what others have done before I start cutting.
#570
Tech Elite
iTrader: (36)
So, I had a chance to have a few local F1 guys look over my newly built kit last night. Overall I think I did a good job, but one of them noted a problem: my rear pod droops down past horizontal. I built everything per the manual as far as I can tell, but it looks like the length of the shock lets the pod droop. I have the shock mounted in the hole closest to the rear pod, and I'm using the shortest shock end screwed all the way in. So... what's the best fix here? I can add spacers to the inside of the shock to limit it's travel, or I could try mounting it in the "middle" hole. Have you guys done either, or did I screw something else up that is causing this droop?