Team Much-More cell master v1
#571
Originally Posted by jas
Does the CM store the settings only after it starts to charge?
I just got a CM and was playing with setting the charge parameters, but didn't let it really start charging because I didn't have a battery pack connected to it. After I switched the unit off and later back on again, it lost the charge parameters that I set. Is this normal? Thanks.
I just got a CM and was playing with setting the charge parameters, but didn't let it really start charging because I didn't have a battery pack connected to it. After I switched the unit off and later back on again, it lost the charge parameters that I set. Is this normal? Thanks.
CM save changes on charge mode after start.
#572
Originally Posted by Guo Chean
Here is one profile for 3700/3800. The newer cells seem to be more sensitive to overcharge, so I would not set the delta peak any higher than 06 or the temp any higher than 48. It is important that the 3700 and 3800 batteries peak below 130 deg Fahrenheit.
Step 1
3050mA 7.0A
Flex off
Step 2
3080 0.2A
Flex off
Step 3
4900mA 4.0A
Flex off
Temp 48
delta peak 05
Step 1
3050mA 7.0A
Flex off
Step 2
3080 0.2A
Flex off
Step 3
4900mA 4.0A
Flex off
Temp 48
delta peak 05
#573
Originally Posted by Ryan Lee
Yes. It is normal.
CM save changes on charge mode after start.
CM save changes on charge mode after start.
#574
Would you recommend the MM 12V cooling fan for the battery or the new "clamp type" heat sink? The battery heat sink looks good, but all that metal so close to the battery pack makes me nervous.
#575
I believe heat sink will be a bit better for the cells for charging and fan is good for cells after run or discharge.
#576
Originally Posted by jas
The battery heat sink looks good, but all that metal so close to the battery pack makes me nervous.
#577
Tech Master
iTrader: (4)
Originally Posted by LazyBug
Hi Guo, can you tell what good is your profile ?? I want to learn more on using this charger. Thanks !
#579
Hi Guo, how long does it complete charging when using your profile ?
#580
Tech Master
iTrader: (4)
Originally Posted by LazyBug
Hi Guo, how long does it complete charging when using your profile ?
4460mah to complete i using the current advantage step charge that hara used on reedy USA setting apply it in CM. not bad i have some different of run time, punch compare to the early setting that orion provide
#581
Tech Master
iTrader: (4)
Hara sets only 5 cells because he is using the Team Orion Discharge Board for his GP3700 and when they just go out of the board the voltage is too low when the charger is checking the battery to be sure it is OK before starting charging. By putting 5 cells it will detect it and start immediately without the need to start twice to make the voltage going up.
Last edited by Guo Chean; 07-12-2007 at 10:14 PM.
#582
Regional Moderator
iTrader: (1)
Originally Posted by Ryan Lee
Yes. It is normal.
CM save changes on charge mode after start.
CM save changes on charge mode after start.
Thanks,
#583
Originally Posted by jas
Would you recommend the MM 12V cooling fan for the battery or the new "clamp type" heat sink? The battery heat sink looks good, but all that metal so close to the battery pack makes me nervous.
SAFE !
#584
Originally Posted by kumpol
Hi Ryan...if I want to store the setting by starting to charge w/o the battery hooked up, would it be ok or not recommended...I see the charger says "Battery Low - Continue"?
Thanks,
Thanks,
It was one and half year ago when I composed CM algorithm. But I just tried it now, it saves correctly. it's ok.
#585
Originally Posted by Guo Chean
Hara sets only 5 cells because he is using the Team Orion Discharge Board for his GP3700 and when they just go out of the board the voltage is too low when the charger is checking the battery to be sure it is OK before starting charging. By putting 5 cells it will detect it and start immediately without the need to start twice to make the voltage going up.
CM will ask " Battery Volt Low Continue? " message if the voltage is extremely low.