Originally Posted by linkless

So I finally got a chance to put my Reventon Pro in my touring car and am running into major issues. I've updated the firmware on the programmer card and in the ESC and so far have tried Stock0 and Mod1 with the same results. Pulling the trigger nets no activity from the motor most of the time. If I roll the spur gear about a half turn and try again it works fine until I stop again. I thought it might be a sensor wire issue but 4 wires and 2 motors later there hasn't been a change in how it's acting. Just to be sure, I put the reventon S back with with the same battery/rx/radio/sensor wire/motor and everything works perfectly and is very smooth. With the Rev Pro it has the issue above and even when it works it doesn't sound very smooth. Has anyone else had this issue and does anyone have any ideas of anything else to try with it?

In case anyone is wondering, KO 408s rx, Futaba BLS351 servo, Novak Ballistic 17.5 motor. The entire setup has worked flawlessly with the Reventon S, the Novak Edge and Novak Kinetic ESC's so I'm quite certain it is something specific to the Reventon Pro.

Originally Posted by NolanP

From what your describing it almost sounds like the hall sensor on the motor. Try a different motor.

Originally Posted by Timbo99

Hi,
Quite a simple fix.
You can't run a 17.5 yet with the current software.It only is suited for motors UP too 10.5.....or lower turns (down to 4.5/4.0).
The software you need will be released soon for 13.5/17.5/21.5.
Just have to wait,shouldn't be far away.
Cheers
Tim

Originally Posted by linkless

If it was doing it on the Stock1 setting I would agree with you. Unfortunately it is doing it with the Stock0 software which is what I need for an upcoming race. I tried a couple of more motors last night including a 13.5 and 4.5 from Speed Passion and they all do the same thing. It happens when I'm running sensored and gets much worse if I run sensorless.

It 'seemed' fine on initial powerup and the issue showed up after updating software.

Originally Posted by Marcos.J

i had a similar issue with it sounds like the motor sensor,

Originally Posted by gdcopbdcop

i can't wait to get the new s/w for 17.5 motors....

Originally Posted by linkless

I guess I need to be more clear, 4 motors that run fine on numerous other ESC's and it gets worse if I try to run sensorless. I'm quite sure it isn't a motor problem.

Originally Posted by Timbo99

As you can see there is NO software for anything above 10.5 yet.
Don't just agree or disagree with me,read the instructions....PLEASE!

Originally Posted by Timbo99

I think I'd be a great Speedpassion tech,I'm on here more,am disabled with one knee shot and live and breath RC.(only hobby sport I can do AND love).
How about it Howard?

Originally Posted by Solara

Timbo99 is correct....

We are going to release a software that will work with motor 10.5 and slower, we have the low and mid range problem take care, but we are now going back to finalize the top end in Thailand. Once this software is approved by the factory driver (we are very confident), this software will be release on SP site and this software will work on ALL MOTORS TURN.

I will say sometime next week....I just receive it 4 hours ago and I will test it tonight.

Originally Posted by Xenolance

This issue only effects the pro correct? I just received a Rev R and it seemed fine on the first run, a bit slow but that was my gearing, I was running 17.5 with stock 0 and a 6.5 FRD just to test it out.. the motor never got above ambient temps :-P Love the ESC so far though, it's really well made and seems high quality.

Originally Posted by linkless

Correct me if I'm wrong, but the software everyone is talking about is the Hybrid Boost (stock1). Is it wrong to assume that the Reventon Pro will work with a 17.5 using the Stock0 software?