|
Originally Posted by mark williams
(Post 7417899)
Hi guys, I'm set to try the 422 software down my club on Friday with v3 10.5
the track has a 20m straight and i was hoping someone has tried it with success..what are the main settings to play with? I don't want it too punchy on the infield but would like to rip down the short straight cheers mark 4/8 9/8 12/6 13/3 14/2 15/3 If you are temping higher than 160*F, then lessen your #15 to 15/4. gearing will depend on your driving. With #15, higher parameters =less punch. Good Luck. After about 2 minutes, check your temps. |
Originally Posted by syndr0me
(Post 7416972)
|
hai, can i used this firmware V1.05_100420.. to run 3t motor?? or this firmware only for stock motor??
|
Originally Posted by wan161111
(Post 7419527)
hai, can i used this firmware V1.05_100420.. to run 3t motor?? or this firmware only for stock motor??
09205_MOD-for mod motors 100422_Stock for Stock Motors 100508_Stock Zero for Zero Timing as per Roar Rules. To answer your question if you use the 09205_Mod software, you can use it with your 3T motor. Yes, you can use the new firmware. |
Originally Posted by charlie_b
(Post 7419553)
The V1.05_100420 has 3 software installed in it.
09205_MOD-for mod motors 100422_Stock for Stock Motors 100508_Stock Zero for Zero Timing as per Roar Rules. To answer your question if you use the 09205_Mod software, you can use it with your 3T motor. Yes, you can use the new firmware. 100422 has added some function. can i used boost n turbocharger with 3t motor or i just can used 09205 firmware to run my 3t motor, without no turbocharger function.. some confuse hehe, |
Originally Posted by wan161111
(Post 7419649)
oo, thanks
100422 has added some function. can i used boost n turbocharger with 3t motor or i just can used 09205 firmware to run my 3t motor, without no turbocharger function.. some confuse hehe, |
Originally Posted by charlie_b
(Post 7419553)
The V1.05_100420 has 3 software installed in it.
09205_MOD-for mod motors 100422_Stock for Stock Motors 100508_Stock Zero for Zero Timing as per Roar Rules. To answer your question if you use the 09205_Mod software, you can use it with your 3T motor. Yes, you can use the new firmware. |
Originally Posted by defcone
(Post 7419661)
Without the turbo charger.
if i used 9.5t sensorless moto, can i used turbocharger.. or this firmware only for sensored stock motor |
Originally Posted by g26er
(Post 7419705)
Just curious... wouldn't 422STOCK with all the timing features turned off be the same as 205MOD? If timing is turned off in 422, what's the difference in the two? Thanks...
You can always mix and match and try out all the software with all type of motor, however, you must be very knowledgable about speed control, along with motor tunning and the latest Supercharger/turbo feature in order for you to take full advantage of the software. You can give the 422 a try by turning the item #12 off and see there are any different to the 205g without the supercharger. |
Originally Posted by wan161111
(Post 7419721)
thanks..
if i used 9.5t sensorless moto, can i used turbocharger.. or this firmware only for sensored stock motor I have not tried anything faster then 10.5 with 422 software, but if I am going to try it, I would do at least 1 setting lower from the 10.5 setup. Speed Passion drivers from Europe has been testing the 422 software with 3.5-4T motor, however, we have yet to receive any recommanded setting for these motor use. See Charlie-B 10.5 setup above and decrease a notch on 9, 12-15 items (don't forget to gear lower then 10.5)and temp motor every 5 laps or so. Let us know your testing....good luck. |
Originally Posted by Solara
(Post 7419783)
YES....you can use 9.5T motor with 422 software. HOWEVER, you must turn down the #9, #12 to #15 features in order to keep the 9.5T motor by blowing up.
I have not tried anything faster then 10.5 with 422 software, but if I am going to try it, I would do at least 1 setting lower from the 10.5 setup. Speed Passion drivers from Europe has been testing the 422 software with 3.5-4T motor, however, we have yet to receive any recommanded setting for these motor use. See Charlie-B 10.5 setup above and decrease a notch on 9, 12-15 items (don't forget to gear lower then 10.5)and temp motor every 5 laps or so. Let us know your testing....good luck. |
Originally Posted by Anemic_SluG
(Post 7415362)
Neutral range is the amount of "play" in the trigger. So the larger the number the more you have to pull the trigger to get the car to go forward or operate the brakes. It doesn't change the cars performance as much as the performance of your radio as a interface to the car. Check out the included picture for clarification.
-j cheers Ali |
Originally Posted by wan161111
(Post 7419721)
thanks..
if i used 9.5t sensorless moto, can i used turbocharger.. or this firmware only for sensored stock motor |
He is using sensorless motor guys, non of us tested this with a sensorless motor. I believe, but can not confirm, the software will not work with an unsensored motor. Please confirm someone?
|
Originally Posted by charlie_b
(Post 7420203)
He is using sensorless motor guys, non of us tested this with a sensorless motor. I believe, but can not confirm, the software will not work with an unsensored motor. Please confirm someone?
|
| All times are GMT -7. It is currently 08:04 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.