eZRUN brushless system
#286
timing
On the Tekmodel 60A esc, what does it do when you change the timing. I have left it alone for fear of messing something up. But if I change the timing will it make the motor faster. I am using a Novk 10.5.
#287
very curious
I plan to run off road and need a system equal to run a 10.5, which do i look to get?
Also, is there a system to buy that will run a 1/8 buggy as an oval L8m?
Also, is there a system to buy that will run a 1/8 buggy as an oval L8m?
#288
yes test done,
i did gear the two cars at 7.8 and done 4 races,2 with each car.
to put it in simple words they did perform identically with only one difference,the ezrun is not as smooth like the sp gt from stop to start.
other than that the same
hard to believe but that was my impression.
would it be different on a bigger race track???i will find out next week on the 7 when i will race on a bigger track with a 5.8 ratio.
i am ordering another one for my F201 and DURGA
REGARDING THE VERSION OF THE EZRUN IT SAY V1.1
i did gear the two cars at 7.8 and done 4 races,2 with each car.
to put it in simple words they did perform identically with only one difference,the ezrun is not as smooth like the sp gt from stop to start.
other than that the same
hard to believe but that was my impression.
would it be different on a bigger race track???i will find out next week on the 7 when i will race on a bigger track with a 5.8 ratio.
i am ordering another one for my F201 and DURGA
REGARDING THE VERSION OF THE EZRUN IT SAY V1.1
#289
just a update:
today my ezrun died.
just stopped wile racing and never came back to life.
the fan speens ,using the programmer does not help it just stays off.
my mate ezrun still cogging like mad
dont know what to say.
looking at some sellers negative feedback on ebay many people seems to have problem with ezrun's.
HOBBYWINGS cannnnnnn you earrrrrrrr meeeeeeeeeeeeee
today my ezrun died.
just stopped wile racing and never came back to life.
the fan speens ,using the programmer does not help it just stays off.
my mate ezrun still cogging like mad
dont know what to say.
looking at some sellers negative feedback on ebay many people seems to have problem with ezrun's.
HOBBYWINGS cannnnnnn you earrrrrrrr meeeeeeeeeeeeee
#291
i tested the motor and is ok,and when it died both motor and esc were not worm at all
#293
Tech Champion
iTrader: (35)
just a update:
today my ezrun died.
just stopped wile racing and never came back to life.
the fan speens ,using the programmer does not help it just stays off.
my mate ezrun still cogging like mad
dont know what to say.
looking at some sellers negative feedback on ebay many people seems to have problem with ezrun's.
HOBBYWINGS cannnnnnn you earrrrrrrr meeeeeeeeeeeeee
today my ezrun died.
just stopped wile racing and never came back to life.
the fan speens ,using the programmer does not help it just stays off.
my mate ezrun still cogging like mad
dont know what to say.
looking at some sellers negative feedback on ebay many people seems to have problem with ezrun's.
HOBBYWINGS cannnnnnn you earrrrrrrr meeeeeeeeeeeeee
What motor were you running?
What motor is your friend running who is cogging?
The only problem I have seen is "cheap charlies" using the ESC beyond its use category
#294
the esc is the 60a with a 10.5 speedpassion sensored(using it without the sensor wire ofcourse),my friend esc still the 60a with a Nosram Dragon 10.5.
they are both V1.1.
they are both V1.1.
#295
Tech Champion
iTrader: (35)
The majority of times you will have cogging issues running sensored motors without sensor wires with a sensorless ESC. Tekin had the same problem with the R1. And especially with motors from 10.5 upwards.
AS for the ESC stopping? I assume you didn't change any settings? Is the fan moving at normal speed or seem slow? If so, unwire the caps and see if it works. Hobbywing taught me this trick if it has a problem with the ESC not working.
AS for the ESC stopping? I assume you didn't change any settings? Is the fan moving at normal speed or seem slow? If so, unwire the caps and see if it works. Hobbywing taught me this trick if it has a problem with the ESC not working.
#296
I purchased an ezrun 35a/13t setup for my touring car while my SP stuff was away for warranty.
What a bargain.
Smooth, powerful enough, easy to use and set up and pretty competitive.
Ive run at 3 meetings now and so far so good. (Fingers crossed)
Of course it could go pop at any moment!!!
In case anyone is interested I run it at around 6fdr.
What a bargain.
Smooth, powerful enough, easy to use and set up and pretty competitive.
Ive run at 3 meetings now and so far so good. (Fingers crossed)
Of course it could go pop at any moment!!!
In case anyone is interested I run it at around 6fdr.
#297
done a full under the bonnet inspection.no lifted tracks or burns anywhere.
i did disolder the top circuit board and no sign of burn there to.
only the fan is working but no soul
i did disolder the top circuit board and no sign of burn there to.
only the fan is working but no soul
#298
Tech Rookie
Ok the brushless dbx is ready!!!
I'll show you some pics to take an idea...
PLease note that the electronics are placed correctly but this is not the final installation.The final will be much better..
The power is PHENOMENAL it tear apart both the front tires and i couldn't give full throttle at any time.
The temperatures was the motor fairly hot (not hot enough though) and the esc cold.
Here are the pics:
Total cost was 200$ including battery motor and esc.
It was worth it every cent...!!!!
I'll show you some pics to take an idea...
PLease note that the electronics are placed correctly but this is not the final installation.The final will be much better..
The power is PHENOMENAL it tear apart both the front tires and i couldn't give full throttle at any time.
The temperatures was the motor fairly hot (not hot enough though) and the esc cold.
Here are the pics:
Total cost was 200$ including battery motor and esc.
It was worth it every cent...!!!!