TRF414M, 404x, 414, 414X
#3423
Tech Master
Nice, but your camber links should be raised up to the top hole. Add at least 2mm spacers under the blocks. If you can get a set of evo4 sway bar holders. That will get the sway bars to the correct height. Looking good
#3424
Tech Master
I need (2) (15t) center pulleys for this car. Anyone have any they're willing to sale?
#3425
Tech Fanatic
iTrader: (34)
http://www.tqrcracing.com/shop/produ....asp?p_id=6083
#3427
Tech Master
I don't know if its the hot ticket. But I go back and forth between 1B-1B and 1C-1C in the front. And 1XA-1D or 1E
#3428
Tech Master
What is the diameter of the top shaft? If the diameter is 4mm, you can use the pulley from 3Racing.
http://www.tqrcracing.com/shop/produ....asp?p_id=6083
http://www.tqrcracing.com/shop/produ....asp?p_id=6083
#3429
Tech Fanatic
iTrader: (34)
#3430
Tech Master
#3431
Tech Elite
iTrader: (8)
Battery options, so I'm deciding on whether to get a shorty, block, or saddle pack. Which one would be the best choice?
As for making a custom chassis, there's a company called Fiberlyte based in the U.K. They already have the lower chassis mocked up already. I might email them and ask them to eliminate the cell holes and narrow the chassis along it's outer edges.
As for making a custom chassis, there's a company called Fiberlyte based in the U.K. They already have the lower chassis mocked up already. I might email them and ask them to eliminate the cell holes and narrow the chassis along it's outer edges.
#3432
Tech Elite
iTrader: (8)
http://www.fibre-lyte.co.uk/fl/cars/tamiya/414ssd.html
So here's the link to the 414M chassis. Now, there are 2 other variants of the chassis. I think this one would do. I'm thinking of asking them to use this layout, but eliminate the battery cutouts and leave the battery loop holes. remove the outer servo hole. Those two unwanted holes on the left hand side.
Narrow the existing width by ?? mm.
Cutouts underneath the pulleys.
Additional holes for optional steering crank system.
Lipo stops?
So here's the link to the 414M chassis. Now, there are 2 other variants of the chassis. I think this one would do. I'm thinking of asking them to use this layout, but eliminate the battery cutouts and leave the battery loop holes. remove the outer servo hole. Those two unwanted holes on the left hand side.
Narrow the existing width by ?? mm.
Cutouts underneath the pulleys.
Additional holes for optional steering crank system.
Lipo stops?
#3433
Tech Master
http://www.fibre-lyte.co.uk/fl/cars/tamiya/414ssd.html
So here's the link to the 414M chassis. Now, there are 2 other variants of the chassis. I think this one would do. I'm thinking of asking them to use this layout, but eliminate the battery cutouts and leave the battery loop holes. remove the outer servo hole. Those two unwanted holes on the left hand side.
Narrow the existing width by ?? mm.
Cutouts underneath the pulleys.
Additional holes for optional steering crank system.
Lipo stops?
So here's the link to the 414M chassis. Now, there are 2 other variants of the chassis. I think this one would do. I'm thinking of asking them to use this layout, but eliminate the battery cutouts and leave the battery loop holes. remove the outer servo hole. Those two unwanted holes on the left hand side.
Narrow the existing width by ?? mm.
Cutouts underneath the pulleys.
Additional holes for optional steering crank system.
Lipo stops?
The rear area where the front suspension blocks are. Needs to be wider for split blocks. And maybe they can redesign the front of the chassis to use the 418 style plastic bumper and push the steering holes back a bit to support 418 style steering rack. And (2) holes for a floating servo mount. Shock towers should be redesigned. 3mm thick, lowered where shorter shocks can fit and camber holes installed. And rear shock tower body post moved to the outside
#3434
TRF414MII swing shaft length
Does anybody know then length of the swing shafts for the TRF414MII??
39mm??
42mm??
I lost one and it is the only part I am missing to complete this car...
Thanks!!
39mm??
42mm??
I lost one and it is the only part I am missing to complete this car...
Thanks!!
#3435
Tech Master