beyondthepack

iTrader: (5)

i think I'm going to take a look at Lowe's, or home depot and see if they sell any material I can use and make 1 peace ride hight adjusters Myself. but what to use, any suggestions as to what might be available?

GWH74

iTrader: (13)

How thin do you want the shims?
Try the hobby shop as they have sheets of material in various thicknesses.
If you need them thin and would like to try some at near zero expense cut up and old drink can.

bfong13

iTrader: (18)

You might want to try the Arm Mount Shim set for the AE TC5. https://www.ssl-stormerhobbies.com/c...ns&pn=ASC31198. These snap in around a 3mm screw on the bulkheads of a TC5 in a similiar manner as the front caster spacers on the 12R5. Give it a try as they're only $4.

xtrememadness

iTrader: (2)

hey guys, just setup my 12r5.1 for 1 cell lipo. do you guys prefer the novak booster or equivalent or lipo reciever pack with voltage regulator. i have the novak booster but it seems a little big thanx

DHMOTORSPORTS

iTrader: (19)

I have been useing a 4 cell nimh pack for the weight on the other side of the car. It helps balance it from left to right. A few guys tried the booster here locally and switched to a rx pack.. Hope it helps..

xtrememadness

iTrader: (2)

thanx dh. appreciate it

Charles Godwin

iTrader: (2)

Right guys n gals. Getting back into electric racing for the winter as nitro 8th outside (on road) is seriously wet . Got a good list so far of what i'm going to buy. R5.1 (ofcourse), KO 951 servo, LRP SXX and 5.5 combo. Now batterys.... been looking into getting Lipo's.

http://www.amainhobbies.com/product_...0C-37V-4900mAh

Been looking at the SMC cells above. Now how many of these do you need for a race day? Would one be sufficient? I know that you need a Lipo charger but would you need to discharge before you recharged them or can you just charge them up without 'maintainance' ? For a charger would you recommend a Much More charger? Would i need any balancing equipment or any further connections? Or would you recommend anything with a inbuilt balancer???

http://www.amainhobbies.com/product_...scharger-Black

http://www.amainhobbies.com/product_...-LiPo-Balancer or

http://www.amainhobbies.com/product_...-LiPo-Balancer

Any help on the battery/charger questions would be greatly appreciated.

Cheers, Chaz

RC MARKET

iTrader: (12)

Yes SMC 50C 4900mAh $5x is best choice battery !
& Can choice ICharger 206B 0.1-20A charge
& w/adj. full charge volt. +-0.01-0.1 !!
you can charge 1 cell to 4.3V cutoff !!

TommyBlazin

iTrader: (29)

has ANYONE found the yokomo sp-4611 brace yet for this car? going crazy looking,pm me if selling one?

andrewdoherty

iTrader: (49)

You could also finger rape a gorilla!! Neither is safe, nor ROAR approved.

PickenStir

Having finger raped many gorillas over the years (mainly ex girlfriends) i can honestly say that it is not as dangerous as once thought.

RC MARKET

iTrader: (12)

around wed back in stock !

Riketsu

iTrader: (34)

Hey guys, does this car have metric screws?

swimbikerun

iTrader: (108)

Yes except for the hardware associated with the rear axle.

Riketsu

iTrader: (34)

Thanks for the response!

What you mean hardware?