CRC 1/10 Pan Car
#226
Shawn.
#228
I run a 10.5, Lipo, with a 50mm rollout. (Technical asphault track)
F/R Weight ratio - 63% Rear
Tire Diameter? - 59mm Rear, 57mm Front
Ride height - 6.5mm Front, 6mm Rear
Droop - 2mm
Camber/Caster/Toe-in - Camber - -0.5, 5Deg Castor, -1 Toe Out
Spring colors front and rear? - Front - Purple CRC, Rear - Stock (Losi Gray?)
Shock oil wt - 40WT
Tire colors - F: GRP Purple R: GRP Magenta (Works Well, nice balance)
or F: GRP Magenta R: Jaco Pink (Not as good a balance, but more traction)
I am still experimenting with foam compounds right now, trying to find the right balance. And the car lacks stablity when going down the straight away, swapped out the servo saver, servo, and double checked the front end setup, found acouple of problems. Will know more on sunday
Shawn.
#230
Tech Champion
iTrader: (73)
I ran the car for the 2nd time today, first time I didn't have access to a truer and ran them fullsize. Our track, 360 Raceway is indoor high bite asphalt, the car pushed on power, I think my best lap was around 12.8. Today I trued the tires, they were smaller than I wanted due to user error, around 2.1" but the car worked so much better. I put the 35lb center spring, thicker tube damping, and a 2mm limiter in the shock. I ran 11.8, the shop owner ran 11.6 with a stop in the lap, so probably an 11.2 clean, much better. I was running 10.5 4 cell, 30/96, rc4less Pink tires. I think its scrubbing a bit, I'll keep playing with the car, it might be good on purple fronts.
#232
Tech Elite
iTrader: (44)
All i can is WOW about this GEN X 10. I also run at 360 like mikexray. I took my car out today and in the main ran an 11.2 with my car. I was the only one with a pan car so i ran with the 19t rubber tire sedans. I ran the car box stock also with rc4less pinks all around. I made a few adjustments to my radio and the car felt awesome. I am running an hpi Murcielago body and it seemed to work well. my car is wearing the front tires a bit but i think it was due to my driving. I drive my touring car a lot smoother than the pan car. This run was on 4 cell with a speed passion 13.5 and an lrp shpere comp.
#233
Tech Adept
i've got a build review of the GENX-10 on my website RCRacer.co.nz
Now all i need, is a servo, brushless system, lipos, and tyres
Argh it's going to be a while till I get it going, damn lack of funds
anyone willing to sponsor my electronics, give me a yell
Now all i need, is a servo, brushless system, lipos, and tyres
Argh it's going to be a while till I get it going, damn lack of funds
anyone willing to sponsor my electronics, give me a yell
Last edited by drivingpro; 06-02-2008 at 12:54 PM.
#235
Tech Master
iTrader: (18)
Awesome write up. I am the opposite of you, I have everything except the kit
i've got a build review of the GENX-10 on my website RCRacer.co.nz
Now all i need, is a servo, brushless system, lipos, and tyres
Argh it's going to be a while till I get it going, damn lack of funds
anyway willing to sponsor my electronics, give me a yell
Now all i need, is a servo, brushless system, lipos, and tyres
Argh it's going to be a while till I get it going, damn lack of funds
anyway willing to sponsor my electronics, give me a yell
#236
Have you tried running some toe-in vs out, or do you lose too much turn in?
#237
Should fit. Its only .5mm longer, and .7mm wider then a trakpower 4900. And this car was obvously designed with the TP4900 in mind.
Shawn.
#238
On the second lap of the first heat my axle snapped. The car is only a month old, and has been badly damaged from a crash acouple of weeks ago.(Another car t-boned mine at full speed at the end of the straight away).
Unfortunately its going to be acouple of weeks before I can get a replacement axle.
Shawn.
#239
Tech Master
iTrader: (18)
Well I grew impatient waiting on this kit and have been searching high and low for 3 days now online for any online store that might have it None found! Today I figured I do another search and there it was one left and snagged that baby. Will ship tomorrow and have it by Saturday priority mail. Man hope all my items arrive at the same time.
Looking for a jr z3650 servo which is all I am missing, anyone?
Looking for a jr z3650 servo which is all I am missing, anyone?
#240
Tech Master
iTrader: (18)
Ok found the jr z3650 and it's on the way.
Shawn or any team crc member, will that .5 lenght and .7mm witdh be a problem trying to fit the lipo I am planning on getting? If anyone can let me know so I can put 3 lipos on order as I don't want to purchase until I am 100% they will fit.
Lipo specs:
Length: 137.5mm
Width: 46.7mm (17.5mm radius sides to emulate stick pack shape)
Height: 23mm (20.5mm height between bumps)
Shawn or any team crc member, will that .5 lenght and .7mm witdh be a problem trying to fit the lipo I am planning on getting? If anyone can let me know so I can put 3 lipos on order as I don't want to purchase until I am 100% they will fit.
Length: 137.5mm
Width: 46.7mm (17.5mm radius sides to emulate stick pack shape)
Height: 23mm (20.5mm height between bumps)