86LikesHpi Pro 4
04-22-2004, 12:28 PM
#3856
That's dialed dude...want to do that to the Losi setup sheets for me? 
04-22-2004, 12:39 PM
#3857
Tech Regular
RC Driver Gary
Looks like to me the Crew Chief approves. You're working on getting a younger racer started I see.
Lookout people. there might be a new up and comer in not too long.
Looks like to me the Crew Chief approves. You're working on getting a younger racer started I see.
Lookout people. there might be a new up and comer in not too long.
04-22-2004, 12:42 PM
#3859
Awesome, you da man! 
04-22-2004, 01:23 PM
#3860
Hebiki, I wasn't going to spend a ton of time on a body that I didn't know if I was going to like or not. If I like it, I'll throw my regular scheme on it.
http://www.rctech.net/forum/attachme...&postid=585027
http://www.rctech.net/forum/attachme...&postid=585027
04-22-2004, 03:22 PM
#3861
cross tightening
when u cross tighten, do you tighten the screw all the way b4 u move to the next or do u tighten gradually so u go over the pattern a few times?
thanks
thanks
04-22-2004, 03:27 PM
#3862
Originally posted by RC Driver Gary
No, that's my daughter, her hair just isn't that long (shut it Troy!). Yeah, she's my buddy.
No, that's my daughter, her hair just isn't that long (shut it Troy!). Yeah, she's my buddy.
tres - I get the same error. I think that the Microsoft Japanese Language pack should fix the problem. btw.
rc_square - I usually get them down close, then re-snug them in the pattern.
04-22-2004, 03:30 PM
#3864
Tech Champion
iTrader: (32)
Join Date: Aug 2001
Location: In a land of mini-mighty mental giants
Posts: 8,854
Trader Rating: 32 (100%+)
rc_square....I say going over the pattern a few times is better then getting one screw all the way tight before the rest are IMO.
Last edited by Kevin K; 04-22-2004 at 03:44 PM.
04-22-2004, 03:41 PM
#3865
Tech Elite
Originally posted by X2
Hey Pops, did u manage to un-tweak ur car?
Hey Pops, did u manage to un-tweak ur car?
Everything else is about done. Looking forward to this weekend to see how well She does compared to the Pro-3 that I was running in Stock before.
04-22-2004, 03:57 PM
#3867
Originally posted by popsracer
...Looking forward to this weekend to see how well She does compared to the Pro-3 that I was running in Stock before.
...Looking forward to this weekend to see how well She does compared to the Pro-3 that I was running in Stock before.
I think you're gonna really like the Pro4
04-22-2004, 04:08 PM
#3868
Re: cross tightening
Originally posted by rc_square24
when u cross tighten, do you tighten the screw all the way b4 u move to the next or do u tighten gradually so u go over the pattern a few times?
thanks
when u cross tighten, do you tighten the screw all the way b4 u move to the next or do u tighten gradually so u go over the pattern a few times?
thanks
takes a few minutes more, but the end result is good..
04-22-2004, 07:24 PM
#3870
Tech Elite
My $.02
Guys;
She leveled out fairly nice on the Tweak board. Less than 1/2 a turn at one end to fix things.
Anyways, here's a picture of the Electronics installation. Everything else is just like all the others.
She leveled out fairly nice on the Tweak board. Less than 1/2 a turn at one end to fix things.
Anyways, here's a picture of the Electronics installation. Everything else is just like all the others.