Alex Racing Barracuda R2 & R3
#8671
Yeah I noticed that, sent Dave a PM before christmas and have not had a relpy, I know he said he was busy at work.....but.......?
#8672
Tech Champion
iTrader: (9)
Re: R2 ARMS?
Originally posted by arn671
Anyone out there have any of the following R2 parts that they are willing to sell:
Mid span arms (regular or hard material) x2 or 3
Long span arms(stock kit) or hard material arms x2
1 deg rear knuckles
axle shims
I think speedtech has everything else but I really need those arms-
Thnaks-Alvin-Seattle-WA
Anyone out there have any of the following R2 parts that they are willing to sell:
Mid span arms (regular or hard material) x2 or 3
Long span arms(stock kit) or hard material arms x2
1 deg rear knuckles
axle shims
I think speedtech has everything else but I really need those arms-
Thnaks-Alvin-Seattle-WA
#8673
Originally posted by Ko Racer
I think there is a reason he doesnt show his head
he doesnt answer any email or pm's Dave you out there ???
I think there is a reason he doesnt show his head
he doesnt answer any email or pm's Dave you out there ???
We miss you Dave We can't go on without your presence
Well, ok, we have a vague sense of loss
And Dave 2, you're setup knowledge is always helpful
#8677
R/C Tech Elite Member
iTrader: (47)
Originally posted by Gazza_D
Yeah I noticed that, sent Dave a PM before christmas and have not had a relpy, I know he said he was busy at work.....but.......?
Yeah I noticed that, sent Dave a PM before christmas and have not had a relpy, I know he said he was busy at work.....but.......?
But I might ask Ko. I'm looking for some 3mm red anodized shims in various thicknesses, anyone know whos got em?
#8678
Tech Champion
iTrader: (9)
Originally posted by AWOLsoldier
1/8th inch huh... guess i'll have some diff balls for sale.
1/8th inch huh... guess i'll have some diff balls for sale.
#8680
Tech Master
iTrader: (1)
Originally posted by Randman
I'm baaaack.
I'm baaaack.
I'm glad you made it back safely. Good job getting your yok hooked up on with so little carpet experience.
I did pretty good in mod, finishing 4th saturday and 6th sunday. I'll post my high-bite foam tire setup a little later. My R2 was smooth and absolutely dialed.
#8681
Help!
Does all Cuda share the same bearings sizes?
R3:
1510x5
850x2
1050x4
1280x4
1060x4
Probably has a slight difference due to the steering?
Does all Cuda share the same bearings sizes?
R3:
1510x5
850x2
1050x4
1280x4
1060x4
Probably has a slight difference due to the steering?
#8682
R/C Tech Elite Member
iTrader: (47)
Originally posted by rc-zombies
I know Jet and Tobee makes them in various sizes...unfortunately not in red. But Square makes these in red:
I know Jet and Tobee makes them in various sizes...unfortunately not in red. But Square makes these in red:
#8683
R/C Tech Elite Member
iTrader: (47)
Originally posted by linger
Randman,
I'm glad you made it back safely. Good job getting your yok hooked up on with so little carpet experience.
I did pretty good in mod, finishing 4th saturday and 6th sunday. I'll post my high-bite foam tire setup a little later. My R2 was smooth and absolutely dialed.
Randman,
I'm glad you made it back safely. Good job getting your yok hooked up on with so little carpet experience.
I did pretty good in mod, finishing 4th saturday and 6th sunday. I'll post my high-bite foam tire setup a little later. My R2 was smooth and absolutely dialed.
You had the Barracuda shirt on Sunday right?
#8685
Regional Moderator
Originally posted by Randman
I might have to settle for those. I was looking for a more thin shim though, like the Evo 3S uses for adjusting the roll.
I might have to settle for those. I was looking for a more thin shim though, like the Evo 3S uses for adjusting the roll.