Tekno RC EB410 Thread
|
|||
#4486
Tech Master
iTrader: (35)
Going 32 pitch is just what the Dr ordered for the track I run on in OK... very loose with a bunch-0-fine rocks.
What would you recommend for a pinion gear to go with that 53t spur?? I am currently running a 26t with the 81t spur. My motor is the Tekin Spec-R 13.5.
Cliff
What would you recommend for a pinion gear to go with that 53t spur?? I am currently running a 26t with the 81t spur. My motor is the Tekin Spec-R 13.5.
Cliff
81/26=3.1153
So you want to find a pinion for a 53t spur that will have similar roll out you take 53 and divide by your answer from the last equation.
53/3.1153=17.012 so a 17t pinion would be what you are going for if you don't want to change the roll out.
53/17=3.1176
#4488
Tech Elite
iTrader: (39)
yeah man that has been my experience too the last two times I was there for practice. It is mainly that quad in the center that is the biggest pain. There is very little room for error and if you hit the first jump just a little off center you end up in the boonies lol. Even a couple of the "fast guys" that I see on Saturdays have a tough time getting through consistently. Needless to say I'm looking forward to the next track change lol
#4489
Tech Legend
iTrader: (294)
Also, is there a brand preference for pinions like how AE pinions for 48 pitch seem to work better (at least ,that is what I am gathering from reading up)
Hmm, be curious if Extoek will have a 32T spur on the way that will fit there motor plate. Have now gone thru 2 spurs (both times motor mount loosened even with threadlock, so will check this more) so if I am in the market for new ones, woudln't mind getting the good stuff Also be good for my daughters vehicle too for more durability.
Last edited by Cain; 07-31-2018 at 07:10 AM.
#4490
Looks like range is 15T-19T from website, that correct as the minimum and maximum sizes?
Also, is there a brand preference for pinions like how AE pinions for 48 pitch seem to work better (at least ,that is what I am gathering from reading up)
Hmm, be curious if Extoek will have a 32T spur on the way that will fit there motor plate. Have now gone thru 2 spurs (both times motor mount loosened even with threadlock, so will check this more) so if I am in the market for new ones, woudln't mind getting the good stuff Also be good for my daughters vehicle too for more durability.
Also, is there a brand preference for pinions like how AE pinions for 48 pitch seem to work better (at least ,that is what I am gathering from reading up)
Hmm, be curious if Extoek will have a 32T spur on the way that will fit there motor plate. Have now gone thru 2 spurs (both times motor mount loosened even with threadlock, so will check this more) so if I am in the market for new ones, woudln't mind getting the good stuff Also be good for my daughters vehicle too for more durability.
No preference on brand, I've even tested Traxxas and Axial pinions.
Exotek making a 32p spur for their diff plate would be cool, if they got enough requests they might do it.
#4497
Tech Legend
iTrader: (294)
You can run down to a 10 tooth for sure, maybe a 9 tooth, and up to at least a 20. I have to see what the actual max is.
No preference on brand, I've even tested Traxxas and Axial pinions.
Exotek making a 32p spur for their diff plate would be cool, if they got enough requests they might do it.
No preference on brand, I've even tested Traxxas and Axial pinions.
Exotek making a 32p spur for their diff plate would be cool, if they got enough requests they might do it.
Got the marching orders, off to message exotek!
For the new shock shaft guides that the ET410 is coming with, will this be a change that the EB410 will be getting as either a running change or will it go into a new version?
#4498
Cool! Good info to add to the wiki and maybe the tekno website too. I am assuming that is the same for the ET410 too right?
Got the marching orders, off to message exotek!
For the new shock shaft guides that the ET410 is coming with, will this be a change that the EB410 will be getting as either a running change or will it go into a new version?
Got the marching orders, off to message exotek!
For the new shock shaft guides that the ET410 is coming with, will this be a change that the EB410 will be getting as either a running change or will it go into a new version?