TLR SCTE 3.0 Thread
#676
15 is a good pinion size for outdoors. For a big indoor track, a 13t is more than adequate. Throw a fan on your motor and go down to a 13t and your temp should be fine. Check your ESC settings and make sure you don't have timing added to the motor.
Also... Make sure your pinion mesh isn't too tight. There's gotta be play between the two gears. A tight pinion mesh will cause it to run hot.
Also, when "Testing" outside... you don't want to run thru the grass wide open. Or run wide open spinning tires & sliding... this isnt a accurate test. Anything run wide open thru grass or run wide open is going to get very hot.
Run it on a track for 5 minute, then temp it. You temps will probably be significantly lower.
Also... Make sure your pinion mesh isn't too tight. There's gotta be play between the two gears. A tight pinion mesh will cause it to run hot.
Also, when "Testing" outside... you don't want to run thru the grass wide open. Or run wide open spinning tires & sliding... this isnt a accurate test. Anything run wide open thru grass or run wide open is going to get very hot.
Run it on a track for 5 minute, then temp it. You temps will probably be significantly lower.
#677
Tech Fanatic
iTrader: (2)
15 is a good pinion size for outdoors. For a big indoor track, a 13t is more than adequate. Throw a fan on your motor and go down to a 13t aand your temp should be fine. Check your ESC settings and make sure you don't have timing added to the motor.
Also... Make sure your pinion mesh isn't too tight. There's gotta be play between the two gears. Tight pinion meshbwill casus it to run hot.
Also... Make sure your pinion mesh isn't too tight. There's gotta be play between the two gears. Tight pinion meshbwill casus it to run hot.
#679
Diff fluid black
This is 1 race day.
Check out tthe photo attached.
Frank Root??? What is causing the diff oil to get so black after one race??
Check out tthe photo attached.
Frank Root??? What is causing the diff oil to get so black after one race??
#680
You don't need to use paper. Just set the gear mesh up so you can rock the gears back and forth a tiny bit. There has to be a bit of movement and space in the gear mesh. Just a tiny bit lol
#682
Tech Prophet
iTrader: (34)
What have I done? I have a 15 tooth pinion gear with stock 40 tooth spur and took it out on the road and front yard to get temp reDings and time it. Big mistake. I got 9 minutes and 22 seconds at a 202 degree temp reading. The race track I'm racing on is this Sunday and this is my first race with it. Should I go down a pinion tooth or things will be different on the small outdoor track? Thanks in advance.
202 is warm but should not damage anything. Also I found (not exactly sure why) but BL motors some times break in and after the first few runs I will see a small temp drop. Bearings working? If the truck is not you have parts wearing in in the drive train as well.
This is very normal. nothing to worry about. Ever gear diff I have ever built on any car big or small turned the oil black.
#685
Tech Fanatic
iTrader: (2)
Charger advice
Any personal opinion on quad multi lipos chargers? I'm running two vehicles in different classes at the same race. I have 10 lipo batteries. I know they cost and that's not the problem. Just need some experience advice on people use them in racing. What brand and model. Like to have all in one unit. Thanks in advance.
#688
Tech Prophet
iTrader: (34)
Any personal opinion on quad multi lipos chargers? I'm running two vehicles in different classes at the same race. I have 10 lipo batteries. I know they cost and that's not the problem. Just need some experience advice on people use them in racing. What brand and model. Like to have all in one unit. Thanks in advance.
https://www.venompower.com/products/...ance-charger-1
independent PS for each channel with 100W per channel is plenty for any 2S-4S application. It is vertically designed to minimize foot space impact in your pit space. Ryan has the quad and I have the duo and both love them.
#689
Tech Fanatic
iTrader: (2)
Venom has a great quad charger
https://www.venompower.com/products/...ance-charger-1
independent PS for each channel with 100W per channel is plenty for any 2S-4S application. It is vertically designed to minimize foot space impact in your pit space. Ryan has the quad and I have the duo and both love them.
https://www.venompower.com/products/...ance-charger-1
independent PS for each channel with 100W per channel is plenty for any 2S-4S application. It is vertically designed to minimize foot space impact in your pit space. Ryan has the quad and I have the duo and both love them.