TLR SCTE 3.0 Thread
#331
Tech Apprentice
Can anyone tell me what size sway bars come with LOSB2222.
Also, are there any set ups out there for a loose dirt large wide open track?
Also, are there any set ups out there for a loose dirt large wide open track?
#337
Tech Initiate
So the scte 3.0 is wider then the 2.0 scte
#338
Tech Master
iTrader: (77)
My SCTE 3.0 arrives tomorrow. I had both the 1.0 and 2.0 a few years back, but recently tried and sold the Tekno. The Tekno is durable as hell for sure, but I never liked how it handled compared to my old SCTEs, so I'm coming back. My SCTE 1.0 and 2.0 had a lot of front center drive shaft wobble and I used to buy the King Headz double bearing center front upright which cured it. Does the 3.0 still have that play and wobble at the front center drive shaft near the center diff?
#339
Tech Apprentice
My SCTE 3.0 arrives tomorrow. I had both the 1.0 and 2.0 a few years back, but recently tried and sold the Tekno. The Tekno is durable as hell for sure, but I never liked how it handled compared to my old SCTEs, so I'm coming back. My SCTE 1.0 and 2.0 had a lot of front center drive shaft wobble and I used to buy the King Headz double bearing center front upright which cured it. Does the 3.0 still have that play and wobble at the front center drive shaft near the center diff?
#340
Tech Apprentice
Race 2,update:
Qualified 2nd. Was leading the main by 20 seconds when I noticed I lost a lot of my punch. About 5 laps in the back left wheel spun off again.....same as last week. The nut was still on and I didn't over tighten them. Since it was the same wheel 2 weeks in a row I'm thinking a bearing went bad. The guy who picked up my truck after the wheel came off said the axel and hex were on FIRE.
Qualified 2nd. Was leading the main by 20 seconds when I noticed I lost a lot of my punch. About 5 laps in the back left wheel spun off again.....same as last week. The nut was still on and I didn't over tighten them. Since it was the same wheel 2 weeks in a row I'm thinking a bearing went bad. The guy who picked up my truck after the wheel came off said the axel and hex were on FIRE.
#342
Tech Apprentice
#344
Tech Adept
the box set-up is not bad at all. i raced mine for the first time this weekend
on a large loose outdoor track. i have a stce 1.0 that is set up really well
for outdoors. 1st qual. the 3.0 had me 8th out of 20. i didn't get much time
to play with it or make changes because i had issues with an other car.
2nd and 3rd qual i had an electronic issue so i had to run the 1.0.
so the 1.0 got me to 10th starting spot out of 12 in the a main. the 3.0 with
box set up got me to a 6th place finish in the a main. thats after getting
taken out on the first lap and actually had to come back from the 12th place.
the 3.0 is awesome. it was a ton better then i thought it would be outdoors.
just try the box set up and see what works
by the way this was not a club race this was the ryan lutz hometown shootout.
#345
Tech Regular
iTrader: (11)
so i'm about half way done with the build... following the instructions... one package at a time. I think i might have screwed something up with the front end.
1. the travel seem really short
2. the inside wheel seems to be turning "well" and the outside wheel seems to be turning short...
i'm looking at the instructions, the car, etc... i cant figure out what i goofed up
FYI, the parts quality is freaking awesome...
1. the travel seem really short
2. the inside wheel seems to be turning "well" and the outside wheel seems to be turning short...
i'm looking at the instructions, the car, etc... i cant figure out what i goofed up
FYI, the parts quality is freaking awesome...