|
Originally Posted by wittyname
(Post 14339444)
For the guys that are just dying to calm this car down with a magic bullet , this is the magic bullet ...
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXVZK3 The single best thing I did to my .2 to settle it down and they made a huge difference. Run them on the rear, and its a pretty quick change. Try either 2mm or 3mm if you find them. I don't run them on my .3 all the time , but they are in the box for those days when I just cannot get my shiz straight. Full disclaimer : Your results may vary .... |
Originally Posted by portyansky
(Post 14339777)
Settle down? Do you have 4 washers in each steering limiter? Also Tekno has a set as well... http://www.teknorc.com/shop/tkr5071c...et-wpins-2pcs/
|
So what springs would u guys recommend for a small medium grip track?
|
What tools do u guys recommend I get with this buggy
|
I just ordered my setup, I'm re-equipping after being away from the hobby for a bit, and wanted to ask what size packs you guys are choosing for mains in the 8-10 minute range? Mostly running on medium to large outdoor tracks.
Looking at Lutz's setup sheet and he's running a 5000mah pack. Cheers! |
Originally Posted by RC Matt
(Post 14340058)
What tools do u guys recommend I get with this buggy
I use the MIP and Hudy hex bits and a Lowe's handle or small electric screw driver. Tekno shock tool and Lowe's Kobalt nut drivers. Needle nose pliers and Tekno or Hudy turnbuckle wrenches. 17mm wheel wrench. I have some other tools in the box, but these are my main ones. |
Hey guys I am about to buy one of these buggies and I was wondering if it mattered which way the servo was on because the one I'm looking at has the knob on the right. I just want to know if it will effect anything or is it fine.
|
Originally Posted by rcjunky10
(Post 14340317)
I just ordered my setup, I'm re-equipping after being away from the hobby for a bit, and wanted to ask what size packs you guys are choosing for mains in the 8-10 minute range? Mostly running on medium to large outdoor tracks.
Looking at Lutz's setup sheet and he's running a 5000mah pack. Cheers! |
Originally Posted by qstorm777
(Post 14340366)
5000 should work on 4S. I have a 5200 and 6500 from SMC just because I wanted to see if there was much of a diff between 60C and 70C. I can't tell a diff.
|
Originally Posted by RC Matt
(Post 14340367)
How much run time do you get with the 6500 and what electronics are you running?
I want to say after 10m main, 2/3 warmup laps included, the 6500 comes off around storage voltage, maybe a little less, but still in the 3.8x per cell range. |
Originally Posted by RC Matt
(Post 14340367)
How much run time do you get with the 6500 and what electronics are you running?
I've ran a 5000 at fear farm and hit Lvc. 5200-5800is ideal due to weight balance |
Could you guys answer my servo question I asked earlier please
|
Originally Posted by RC Matt
(Post 14340397)
Could you guys answer my servo question I asked earlier please
Not this |\ Refer to the manual or Tekno website. |
Originally Posted by RC Matt
(Post 14340365)
Hey guys I am about to buy one of these buggies and I was wondering if it mattered which way the servo was on because the one I'm looking at has the knob on the right. I just want to know if it will effect anything or is it fine.
|
22 minutes tekin rx8 and 2050kv motor 6500mah smc and 16 or 17 minutes with turnigy 5000mah 20c (a lot less punch too)
|
| All times are GMT -7. It is currently 03:56 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.