Tekno RC EB48.3 Thread
|
|||
#2446
Would this be ok on 2S with a 23T pinion for bashing ? or is the .3 too heavy for it and will cause overheating? (motor has a fairly long can, 72mm)
http://www3.towerhobbies.com/cgi-bin...&I=LXFEYN&P=ML
Cheers.
http://www3.towerhobbies.com/cgi-bin...&I=LXFEYN&P=ML
Cheers.
#2448
Would this be ok on 2S with a 23T pinion for bashing ? or is the .3 too heavy for it and will cause overheating? (motor has a fairly long can, 72mm)
http://www3.towerhobbies.com/cgi-bin...&I=LXFEYN&P=ML
Cheers.
http://www3.towerhobbies.com/cgi-bin...&I=LXFEYN&P=ML
Cheers.
#2449
But if 16T is enough for long straights on big tracks to keep up with the 4S crowd (bashing fun, not official racing), then I will go with 16-18T tops.
Thanks mate.
#2450
#2451
#2452
I have 4 2S packs and running on 2S power would literally double up my running time at the far-away desert track, it would be highly appreciated if you could recommend a more suitable 2S system, or should I just get a new kit ?(my wallet really hurts)
Cheers again.
#2453
Tech Master
Forgive my ignorance, but how much heavier is the 0.3 than the SL or SCT ? and these lighter kits usually run 36x65mm cans without issues, while this one is 36x72mm. And ammm, I bought the combo 2 days ago (should've asked 1st, but I'm very smart).
I have 4 2S packs and running on 2S power would literally double up my running time at the far-away desert track, it would be highly appreciated if you could recommend a more suitable 2S system, or should I just get a new kit ?(my wallet really hurts)
Cheers again.
I have 4 2S packs and running on 2S power would literally double up my running time at the far-away desert track, it would be highly appreciated if you could recommend a more suitable 2S system, or should I just get a new kit ?(my wallet really hurts)
Cheers again.
Also, Vent that body well for airflow. I used a body punch to put holes all through the windshield, along with teh normal venting.
#2454
I wouldn't be worried about running the .3 on 2s. I do for indoors, and my buddy does for outdoors, Both of us ran the hobbywing 4700kv motor with a 16t pinion without issue. With that 4.5 being in the 5000kv range, I would have to guess 15t, maybe 14t...I don't believe you can physically fit smaller than a 14t in the motor mount and get the mesh correct.
Also, Vent that body well for airflow. I used a body punch to put holes all through the windshield, along with teh normal venting.
Also, Vent that body well for airflow. I used a body punch to put holes all through the windshield, along with teh normal venting.
#2455
Tech Master
iTrader: (10)
Has anyone tried the new recommended indoor setup from Tekno's website?
http://www.teknorc.com/wp-content/up...d%20Indoor.pdf
I am having troubles getting the front camber to -2deg with how short the camber links are, the turnbuckle feels like its bottoming out and binding up the pivot balls.
http://www.teknorc.com/wp-content/up...d%20Indoor.pdf
I am having troubles getting the front camber to -2deg with how short the camber links are, the turnbuckle feels like its bottoming out and binding up the pivot balls.
#2456
Tech Regular
Has anyone tried the new recommended indoor setup from Tekno's website?
http://www.teknorc.com/wp-content/up...d%20Indoor.pdf
I am having troubles getting the front camber to -2deg with how short the camber links are, the turnbuckle feels like its bottoming out and binding up the pivot balls.
http://www.teknorc.com/wp-content/up...d%20Indoor.pdf
I am having troubles getting the front camber to -2deg with how short the camber links are, the turnbuckle feels like its bottoming out and binding up the pivot balls.
#2457
Tech Regular
iTrader: (6)
More bump out gives more mid corner steering.
Hey Matt, who else is stocking your low frequency springs right now? I'm looking for the black fronts and orange rears and teknorc.com and http://www.fiercercsolutions.com/ are both out of stock.
Hey Matt, who else is stocking your low frequency springs right now? I'm looking for the black fronts and orange rears and teknorc.com and http://www.fiercercsolutions.com/ are both out of stock.