TLR TEN-SCTE 2.0 Kit Thread
#3541
@hacker, I mentioned before my rear ring gear tore 2 teeth off and I had ordered one but the way it mounted was backwards so I think I ordered the wrong one, should I just contact HH and get a replacement which I should of in the first place?
#3542
Hay guys,
Where can I buy the new carbon shock towers? I noticed the rear tower, it's not broke but the top layer of carbon is splintered, just about an 1/8 of an inch on the edge in the center right next to where it bolts to the case. I'm thinking of just putting some CA glue on it and running it. It's not bent, I don't think carbon bends. So, where can I get these if I have to end up replacing it?
I also broke a part on the steering bell crank. Should I just pay $6 for another plastic set or pay $35 for a complete alum. set? I have noticed that over the last week there has been a lot of slop in the steering. Is this normal? It looks like it is in the plastic rod ends. Do these need to be replaced often?
Ok, last question.
I have already replaced two CVD pins in the center drive line ( front and rear). I have been told that I should upgrade to the, dare I say it, Hekno CVDs because they are stronger and last longer. Has anyone replaced there center CVDs and front and rear dog bones?
Going to rebuild my truck and also order some avid revolution bearings to get ready for the out door season.
Thanks guys.
Where can I buy the new carbon shock towers? I noticed the rear tower, it's not broke but the top layer of carbon is splintered, just about an 1/8 of an inch on the edge in the center right next to where it bolts to the case. I'm thinking of just putting some CA glue on it and running it. It's not bent, I don't think carbon bends. So, where can I get these if I have to end up replacing it?
I also broke a part on the steering bell crank. Should I just pay $6 for another plastic set or pay $35 for a complete alum. set? I have noticed that over the last week there has been a lot of slop in the steering. Is this normal? It looks like it is in the plastic rod ends. Do these need to be replaced often?
Ok, last question.
I have already replaced two CVD pins in the center drive line ( front and rear). I have been told that I should upgrade to the, dare I say it, Hekno CVDs because they are stronger and last longer. Has anyone replaced there center CVDs and front and rear dog bones?
Going to rebuild my truck and also order some avid revolution bearings to get ready for the out door season.
Thanks guys.
#3544
Hay guys,
Where can I buy the new carbon shock towers? I noticed the rear tower, it's not broke but the top layer of carbon is splintered, just about an 1/8 of an inch on the edge in the center right next to where it bolts to the case. I'm thinking of just putting some CA glue on it and running it. It's not bent, I don't think carbon bends. So, where can I get these if I have to end up replacing it?
Where can I buy the new carbon shock towers? I noticed the rear tower, it's not broke but the top layer of carbon is splintered, just about an 1/8 of an inch on the edge in the center right next to where it bolts to the case. I'm thinking of just putting some CA glue on it and running it. It's not bent, I don't think carbon bends. So, where can I get these if I have to end up replacing it?
https://www.google.com/search?q=go&a...w=1366&bih=667
#3545
Battery Thumb Screws (2): SCTE 2.0 mine just came end and only had one thumb screw in it package and picture says two.
#3546
Battery Thumb Screws (2): SCTE 2.0
by: Team Losi Racing
Avg. Customer Rating: 0.0 (0) .
Item: TLR231003
Ships in: Backordered
Price: Reg. $5.99 $5.99
Qty.
Add To Cart Add to Wish List
by: Team Losi Racing
Avg. Customer Rating: 0.0 (0) .
Item: TLR231003
Ships in: Backordered
Price: Reg. $5.99 $5.99
Qty.
Add To Cart Add to Wish List
#3547
well can not get pic to post
#3548
Tech Master
iTrader: (40)
Always glue edges of c/f before you instàll them to prevent delamination
You prob need new rod ends n ball links
I have broken a bell crank n replaced with alloy
Get the m2c coupler pin keepers so the dont fly out of the plastic coupler retainer
I hear teckno stuff wears just as fast
Did i cover all Q?
You prob need new rod ends n ball links
I have broken a bell crank n replaced with alloy
Get the m2c coupler pin keepers so the dont fly out of the plastic coupler retainer
I hear teckno stuff wears just as fast
Did i cover all Q?
#3550
Yeah, those never passed QC and got put into stock on accident. About 60-70 of them made it out before I caught it and pulled the rest from stock. They were packaged wrong.
#3551
Tech Apprentice
iTrader: (3)
Casper, I called horizon over two weeks ago to get the shock caps and a sway bar link that was missing from my kit. They said it would ship in a couple days. Still haven't received them. Are they out of stock or what's the issue? Getting tired of having to use pliers to take my shocks apart.
#3553
#3554
Tech Master
iTrader: (1)
At some point it does affect the truck a bit,but not for a long while. What I tell people who are concerned with this is to: With the steering trim adjusted correctly run your car full throttle down the strait away and let go of the wheel,truck will continue to track forward and strait(if set up correctly) with all that slop.... Cheers...