Losi 1/10 TEN-SCTE ARR 4x4 Short Course Truck Thread
#8011
Yes it is all four plates. Pricing will depend on what thickness material I settle on. So pricing right now would be premature. Give me a few days and we can go from there.
As I started getting the weight out of my truck I noticed better acceleration, the ability to gear higher, jump better, handle quicker, etc.. Some of that could be due to the corrected balance of the truck also. I think Salad weighed his in at 6lbs 11oz, which is almost what mine weighed out of the box but I used a lighter battery than him. As of right now my truck chimes in at 5.9lbs and getting lighter by the day. lol.. A RTR goal would be 5-5.25lbs.. At least thats what I am working towards.
As I started getting the weight out of my truck I noticed better acceleration, the ability to gear higher, jump better, handle quicker, etc.. Some of that could be due to the corrected balance of the truck also. I think Salad weighed his in at 6lbs 11oz, which is almost what mine weighed out of the box but I used a lighter battery than him. As of right now my truck chimes in at 5.9lbs and getting lighter by the day. lol.. A RTR goal would be 5-5.25lbs.. At least thats what I am working towards.
Since the class minimum is 5.5lbs, as close to that as possible is what I'm shooting for. I have a ways to go
#8013
Those were the good old days
Burned a few checkpoint, trinity tony nisenger series and reedy motors too
insane rpm but 3-4 min runs with nicd or nimh
ok looking for a new scte for trade with a mbx6e roller
anyone know where i can buy a new scte
any hobby shops, need it soon for rc pro series race
Burned a few checkpoint, trinity tony nisenger series and reedy motors too
insane rpm but 3-4 min runs with nicd or nimh
ok looking for a new scte for trade with a mbx6e roller
anyone know where i can buy a new scte
any hobby shops, need it soon for rc pro series race
RC speed zone
#8014
My scte is on its way! Now I just need pinion gear for my cc 3800 please help!
#8015
#8017
hearing about this 4-pole sensored motor from tekin, love to know if it is gonna be more 540 size or 550 sized? that sc4x motor looked huge love to go with a smaller motor if I could. was gonna switch from 1415 to 1410, but if that tekin motor is similar to the 1410 I'm waiting on that one.
#8018
Tech Adept
Mailman showed up today with Chrispins & Horizon pins both in the same delevery!! Which ones should I put in?? Or should I just flip a coin to decide?
#8019
I have two trucks and told horizon that, but they only sent me one set of pins. I already put in chris pins in one of them, so I guess it's ok, I just wish they would have sent both sets.
#8020
#8021
Tech Adept
#8022
My Tenshock motor got here yesterday, just got back from the post office... Not bad, you can't tell it's not the quality of the Castles but as long as it works who cares. I got the 5200kv version, which I don't plan on using in the Losi (to heavy).
On another note... Rage got shot by his crazy ass neighbor yesterday, but is fine. Glock 40 don't phase the rage.
On another note... Rage got shot by his crazy ass neighbor yesterday, but is fine. Glock 40 don't phase the rage.
#8023
#8024
#8025
His neighbor was throwing stuff at his dog from the other side of the fence, when Rage went outside to see wtf was up, dude pulled a gun and fired 3 shots. The guys in jail right now with 2 felony charges.
So make sure and run your packs down to LVC, cause you never know when it might be your last pack.
So make sure and run your packs down to LVC, cause you never know when it might be your last pack.