Losi 1/10 TEN-SCTE ARR 4x4 Short Course Truck Thread
The Proline V3 foams hold up a lot better than the SC foam that Proline includes with there tires. Proline softened up the SC foam with the inner groove and those foams die and feel way too soft after only a few runs.
The only thing I didn't like about the HB Beams is that on my SCTE is that they balloon quite a lot. I run the Pro4 4600 and with that kind of power they grow too much IMHO. I would try what was posted about gluing the outer ribs to the rim, that might just be the trick.
BulldogSRT
The only thing I didn't like about the HB Beams is that on my SCTE is that they balloon quite a lot. I run the Pro4 4600 and with that kind of power they grow too much IMHO. I would try what was posted about gluing the outer ribs to the rim, that might just be the trick.
BulldogSRT
I just wanted to post this up because my results were staggering. I finaly got around to putting the v2 dual stage scte pistons(rcshox) in my truck this last friday, and did alot of tuning. My previose fastet lap at our track was 35s, well after some tuning and playin around with tires, I was able to best my previous fastet lap by 1.5s
and i was able to hit 12 laps for the first time in a 7min main, and if I had run perfectly clean, I have no doubt that i could hit 13 laps. I was blown away! I hit several 33.5s which is very fast.
Oh, and I ordered the 120mp esc from brushlesshobbies.com for 59$ and found that it is the exact esc as the Xerun 120amp esc. Its an amazing deal. It ran great all friday. The esc never got over 110degs running the pro 4 4000kv 15/40 with 20deg of turbo, and the mtor didnt get over 160.
and i was able to hit 12 laps for the first time in a 7min main, and if I had run perfectly clean, I have no doubt that i could hit 13 laps. I was blown away! I hit several 33.5s which is very fast.
Oh, and I ordered the 120mp esc from brushlesshobbies.com for 59$ and found that it is the exact esc as the Xerun 120amp esc. Its an amazing deal. It ran great all friday. The esc never got over 110degs running the pro 4 4000kv 15/40 with 20deg of turbo, and the mtor didnt get over 160.
Do the Losi 8ight rod ends fit the SCTE pivot balls? What are the tie rods of choice the 8ight or Lunsford? I ordered the 8ight rod ends but do I also need the 8ight balls?
Tech Elite
iTrader: (27)
Hehe, yes i do I really liked the AE, until we had a new track layout with a set of quads and a 35' tripple that would kill the AE, while the losi could sky it. Now after amonth of driving the losi, I have been learning how to drive real hard. I couldnt drive the AE nearly as hard.
Hehe, yes i do I really liked the AE, until we had a new track layout with a set of quads and a 35' tripple that would kill the AE, while the losi could sky it. Now after amonth of driving the losi, I have been learning how to drive real hard. I couldnt drive the AE nearly as hard.
Tech Master
iTrader: (40)
the new ha balls fit in the 2.0 rod ends!! and i use the mounts to the towers of the eight as well. the 2.o balls dont fit in the front hub or the rear hubs. i bought off an ebay seller thats scraps new kits and been running 2.0 rods n ends since i first got the scte.
Tech Master
iTrader: (145)
Tech Champion
iTrader: (168)
However if you machine down the back of the LOSB3499 hubs and use LOSB3566 axles (the ones from the Ten-T) you can get the truck very close to ROAR legal width with the tires fully inside the body. Speaking from experience...
Tech Master
iTrader: (40)
Tech Addict
iTrader: (37)
Just wanted to let you guys know I have 2 Brand new never used 6.6 nano techs for sale. I'm asking 60 shipped each. Pm me if your interested.
Tech Elite
iTrader: (110)
I just wanted to post this up because my results were staggering. I finaly got around to putting the v2 dual stage scte pistons(rcshox) in my truck this last friday, and did alot of tuning. My previose fastet lap at our track was 35s, well after some tuning and playin around with tires, I was able to best my previous fastet lap by 1.5s
and i was able to hit 12 laps for the first time in a 7min main, and if I had run perfectly clean, I have no doubt that i could hit 13 laps. I was blown away! I hit several 33.5s which is very fast.
Oh, and I ordered the 120mp esc from brushlesshobbies.com for 59$ and found that it is the exact esc as the Xerun 120amp esc. Its an amazing deal. It ran great all friday. The esc never got over 110degs running the pro 4 4000kv 15/40 with 20deg of turbo, and the mtor didnt get over 160.
and i was able to hit 12 laps for the first time in a 7min main, and if I had run perfectly clean, I have no doubt that i could hit 13 laps. I was blown away! I hit several 33.5s which is very fast.
Oh, and I ordered the 120mp esc from brushlesshobbies.com for 59$ and found that it is the exact esc as the Xerun 120amp esc. Its an amazing deal. It ran great all friday. The esc never got over 110degs running the pro 4 4000kv 15/40 with 20deg of turbo, and the mtor didnt get over 160.
Tech Elite
iTrader: (27)
Good to hear some feedback on the speedo. I talked to one of the better racers at the onroad track the other day and he said the Hobbywings are really solid. Smoothe like Lrp with Tekin punch. Not to mention I could sell my back up RS pro and buy 3 of these.. So you don't need a card or anything but a usb cable to program these?
Anyone looking to unload a new / like new RTR losi 550 2800kv motor that upgraded? LMK.