Durango DEX210 Thread
#1216
22 Spur will also be too small as they have the same hole diameter as the B4.
#1217
can anyone else help me on what other then airtronics servo i should get for my 210 since im going to be useing a tekin rs esc and a 13.5 ballistic motor
thanks,,,brian
thanks,,,brian
#1219
Finally got mine all done, anyone have any issues with binding in either of the rear axle joints? I'm getting a clicking out of one side, and the height of the arm actually changes if you slowly rotate that side, almost like axle cup is bent. Haven't pulled it apart to try a different set of holes yet but wanted to check to see if anyone else had problems?
Randy, Did you remove the rear droop screws or is it full droop with them in?
#1221
Tech Fanatic
iTrader: (38)
Join Date: Jul 2007
Location: Somewhere between raising hell and Amazing Grace
Posts: 761
Trader Rating: 38 (100%+)
Finally got mine all done, anyone have any issues with binding in either of the rear axle joints? I'm getting a clicking out of one side, and the height of the arm actually changes if you slowly rotate that side, almost like axle cup is bent. Haven't pulled it apart to try a different set of holes yet but wanted to check to see if anyone else had problems?
Randy thanks for posting the setup, I'm starting from there. My track should be a med-high bite track, indoor clay. I know it's a tough gig having to go out and play with your new buggy all day and figure out a starting setup, but someones gotta do it right?
-rocky b
Last edited by flatspunout; 10-26-2011 at 03:36 AM.
#1222
I have a theory for the ball cup popping, for those are having problem, will you guys happen to use the little holes on the ball cup as a levage when you are building the turn buckle? Will there be any chance you may already deform the ball cups when you are building it? Just my 2 cents.
#1223
Was putting shocks on the car last night. Noticed one of the standoffs (Part# 330312-3) wasn't completely molded. I looked to see if they were available online, but couldn't find any. Anyone know if the big bore fr/rr metal standoffs will work? Will probably call TD for a replacement too.
#1224
It happens without the tranny in as well, it's definitely in the axle somewhere. Good thought though as you can definitely see a potential clearance issue if you don't give that extra turn to the diff screw!
#1225
Oh and regarding the diff on this buggy......it's absolute BUTTER!!!! ranks right up there with my Schumacher diffs in the unbelievably smooth department! Nice job TD.....
#1226
#1227
Tech Champion
iTrader: (14)
Was putting shocks on the car last night. Noticed one of the standoffs (Part# 330312-3) wasn't completely molded. I looked to see if they were available online, but couldn't find any. Anyone know if the big bore fr/rr metal standoffs will work? Will probably call TD for a replacement too.
http://www.amainhobbies.com/product_...ck-Mount-Set-2
and this...
http://www.amainhobbies.com/product_...vot-Ball-Set-4
And then use the metal nut that holds the shock screw on the tower to hold the metal unit on. This new piece will allow for quicker shock tuning.
#1228
This is what you will need to convert to metal...
http://www.amainhobbies.com/product_...ck-Mount-Set-2
and this...
http://www.amainhobbies.com/product_...vot-Ball-Set-4
And then use the metal nut that holds the shock screw on the tower to hold the metal unit on. This new piece will allow for quicker shock tuning.
http://www.amainhobbies.com/product_...ck-Mount-Set-2
and this...
http://www.amainhobbies.com/product_...vot-Ball-Set-4
And then use the metal nut that holds the shock screw on the tower to hold the metal unit on. This new piece will allow for quicker shock tuning.