Durango DEX210 Thread
#4561
If you're talking about the Mamba Max Pro it's the sensored version and the fan is in a removable case which is why the fan plug is external, so you can remove it as its not needed in 2wd. If its the older Mamba Max non sensored unit then it's a bit more work to get the fan out.
#4563
yes until you put the 6mm in, then it calms it down.
#4564
Tech Fanatic
iTrader: (18)
I saw some of 22's running that much up front. My track is indoor clay as well. This is the first year, so we are still guessing on a lot of things. Right now the track temps are ranging from 25-35 deg F, so even though it should be high bite it gets a little slick. I think I've got the front dampening pretty close, but still uncertain on the rear. It's a big 1/8th scale type layout. Last week I tried 4x1.2 with 27.5, 3 upper & 2 lower, dk green springs. Next time, I'm dropping to 22.5 and moving the lower to 3.
#4565
I saw some of 22's running that much up front. My track is indoor clay as well. This is the first year, so we are still guessing on a lot of things. Right now the track temps are ranging from 25-35 deg F, so even though it should be high bite it gets a little slick. I think I've got the front dampening pretty close, but still uncertain on the rear. It's a big 1/8th scale type layout. Last week I tried 4x1.2 with 27.5, 3 upper & 2 lower, dk green springs. Next time, I'm dropping to 22.5 and moving the lower to 3.
#4566
Tech Master
iTrader: (26)
Saw these today:
http://tresreyusa.blogspot.com/2012/...l#comment-form
Can't tell if these are to add toe, or remove it, or change to the number on the block. They mention having +2 blocks in, but does that add 2 degrees, remove it, or change to 2 degrees assuming 0 inserts?
http://tresreyusa.blogspot.com/2012/...l#comment-form
Can't tell if these are to add toe, or remove it, or change to the number on the block. They mention having +2 blocks in, but does that add 2 degrees, remove it, or change to 2 degrees assuming 0 inserts?
#4567
Tech Elite
iTrader: (141)
Saw these today:
http://tresreyusa.blogspot.com/2012/...l#comment-form
Can't tell if these are to add toe, or remove it, or change to the number on the block. They mention having +2 blocks in, but does that add 2 degrees, remove it, or change to 2 degrees assuming 0 inserts?
http://tresreyusa.blogspot.com/2012/...l#comment-form
Can't tell if these are to add toe, or remove it, or change to the number on the block. They mention having +2 blocks in, but does that add 2 degrees, remove it, or change to 2 degrees assuming 0 inserts?
#4571
you guys know any gold turnbuckles I could use? to pimp my camber/steering links ?
#4572
My guess would be + refers to positive (naturally) and the number is total toe, not added toe. These would be for use with the toe inserts in the hub carrier. Removing toe at the arm mounts and adding it back in the hubs would increase the wheelbase if you don't change the arm spacing. The Cougars a ways back used this arrangement somethimes.
#4573
Momba max pro
The mmp fits snug in my 210. It is all i run. My sens wire comes out the back. And i took my dremel with a 1/4" drum and shaved a little off the left front corner of the pod. Picks will be available if needed. Works perfect and has not come out yet.
#4574
What size is the inner bearing on the lay shaft. I've gone through two from boca and 1 of the original. Make any suggestions?
#4575
Tech Elite
iTrader: (42)
Join Date: Jun 2008
Location: anywhere I can race 2wd dirt,and 1/12 onroad in MI.
Posts: 3,891
Trader Rating: 42 (100%+)
sounds as if you need to shave a little off the top shaft spacer.Going through that many bearings there has to be a reason, and i know with mine when I went to do the tranny Mine needed a little shave to get everything to spin nice and free..I ended up taking about .005" off the length of the top shaft spacer to get her freed up..