2004 AARCMCC ACT Titles
#106
Entry Correction
Nerdling,
When would an updated list be up in your site.
Dan Garcia
When would an updated list be up in your site.
Dan Garcia
#107
Late Entries
Guys,
just to let you know, any entries recived from this morning will attract a $15 sur charge.
I'm still quite happy to accept late entries, just be aware of the additional cost.
I'll update the entry list on the website later tonight.
Gotta go make that crystal board from practict on Friday.
cheers
just to let you know, any entries recived from this morning will attract a $15 sur charge.
I'm still quite happy to accept late entries, just be aware of the additional cost.
I'll update the entry list on the website later tonight.
Gotta go make that crystal board from practict on Friday.
cheers
#110
Tech Master
iTrader: (22)
Join Date: Aug 2003
Location: Where there's smoke there's a tyre
Posts: 1,786
Trader Rating: 22 (100%+)
i need some clarification for some rules in the arcmac stock class. whats the minimum ride height? and what is the maximum wheel and tyre width? the arcmac rules (may be an old version) says you can run 28mm wide tyres but only 26mm wide rims, what if i want to run 28mm wide foam tyres? to i have to chop the rim down?
#112
Qualifying
It's changed. With the unexpected umber of entries (thanks guys) we've had to reduce the number of rounds of qualifying to three (down from four). This will see racing finish at 9.30pm (previously 10.50pm) on Saturday and 4pm (previously 5.10pm) on Sunday.
#114
Originally posted by scottyhill
Well, I could always pull out if that will make it any easier?
Sounds like a could problem to have.
Well, I could always pull out if that will make it any easier?
Sounds like a could problem to have.
Normally on carpet 3mm is the min ride height but I would say you need to run a little more than this as it's a longer pile than ozite. 26 is the max width, 28 was to cover tire bead.
Coxy.
#115
Well, I could always pull out if that will make it any easier?
No Scott don't pull out.
Normally on carpet 3mm is the min ride height but I would say you need to run a little more than this as it's a longer pile than ozite. 26 is the max width, 28 was to cover tire bead.
#116
Ride Height
Ride height for ISTC is 5mm.
Rim width is 26mm, the tyre can have a max width of 28mm.
In the case of rubber tyres, the tyre can over hang the rim by 2mm in total with the bag of the side wall of the tyre.
You could try and true your foam tyres the same way if you like ?
Pretty straight forward when you read the rules that are on the AARCMCC web site.
Rim width is 26mm, the tyre can have a max width of 28mm.
In the case of rubber tyres, the tyre can over hang the rim by 2mm in total with the bag of the side wall of the tyre.
You could try and true your foam tyres the same way if you like ?
Pretty straight forward when you read the rules that are on the AARCMCC web site.
#117
Have we all returned the from the Capital of RC?
ACT titles completed and a good meeting it was, great racing , great track, the club did a great job. How good was the indoor weather lol, those heaters were fantastic.
Alycat again caused issues, this time the club handled the situation "very" well and progressed the meeting as best possible. The issues mainly annoy races as we don’t get to see accurate race times, consistency etc and in bad cases skewed results.
BTW: who won concourse?
ACT titles completed and a good meeting it was, great racing , great track, the club did a great job. How good was the indoor weather lol, those heaters were fantastic.
Alycat again caused issues, this time the club handled the situation "very" well and progressed the meeting as best possible. The issues mainly annoy races as we don’t get to see accurate race times, consistency etc and in bad cases skewed results.
BTW: who won concourse?
#118
What happen to the Plow4
BK, How did you go in both class. Would you have done better with the Pro4.
#119
Originally posted by black-knight
BTW: who won concourse?
BTW: who won concourse?
Thanks Nerd and all the crew for another great "Titles". Indoor weather rocked! and in the end you guys did well to deal with the gremlins at play.
Cheers
Andy
#120
Re: What happen to the Plow4
Originally posted by danjoy25
BK, How did you go in both class. Would you have done better with the Pro4.
BK, How did you go in both class. Would you have done better with the Pro4.
Qualified 4th in Stock and 7th in mod, both with Assassins. Stock car was very good, but i did not pay enough attention to my stock motor service. Stuffed up first final with wrong tires and ran a test motor in 2nd final so got DQ'd, did not run 3rd final. So i assume i got 10th as a final position.
Mod was fun, not sure where i finished.?