387LikesJConcepts Thread
03-08-2007, 10:11 PM
#46
hey andy moore. for those who dont know who u are. can you tell us who you are and what your association with j-concepts is.
also can you tell me is the BJ4WE on a waiting list?
thanks
also can you tell me is the BJ4WE on a waiting list?
thanks
03-09-2007, 04:00 AM
#47
I know there is still a BJ4x4 WE on the shelf at my local Hobby Shop.
Wolcott Hobbies
http://www.WOLCOTTHOBBY.com/
(203) 879-7766
I beleive they will take credit card over the phone and ship and also take paypal.
Wolcott Hobbies
http://www.WOLCOTTHOBBY.com/
(203) 879-7766
I beleive they will take credit card over the phone and ship and also take paypal.
03-09-2007, 04:11 AM
#48
Tech Regular
JConcepts WING AND BODY 
Jammin' X1CR PRO
Jammin' X1CR PRO
03-09-2007, 06:12 PM
#50
Originally Posted by PIITB
hey andy moore. for those who dont know who u are. can you tell us who you are and what your association with j-concepts is.
also can you tell me is the BJ4WE on a waiting list?
thanks
also can you tell me is the BJ4WE on a waiting list?
thanks
Im just someone who works there, as well as a veteran racer. I figured I would cut down on our email load a little by answering some common questions, and also offering a place to discuss the products.
Haha, thanks Paul!
03-09-2007, 07:08 PM
#51
Tech Addict
Well I have done it. And it wasn't really all that involved. I have adapted the AE RC10GT2 steering cranks and servo saver to my BJ4WE. I haven't run it yet so I'll hold off on posting pics until I get it sorted out.
I was amazed that the cranks matched so perfectly other than their length end to end where they mount into the bearings.
I had to move the crank that connects to the servo horn to the opposite side of the car and move the servo back by flipping the mounts to the front and drilling new holes. Then I'm going to have to mount the receiver in front of the motor (which concerns me, we'll see).
I was even able to use the stock bearing cerriers top and bottom. Although I did have to capture the bearings.
I'll update on how it works and post pics if it works well.
I was amazed that the cranks matched so perfectly other than their length end to end where they mount into the bearings.
I had to move the crank that connects to the servo horn to the opposite side of the car and move the servo back by flipping the mounts to the front and drilling new holes. Then I'm going to have to mount the receiver in front of the motor (which concerns me, we'll see).
I was even able to use the stock bearing cerriers top and bottom. Although I did have to capture the bearings.
I'll update on how it works and post pics if it works well.
03-09-2007, 10:47 PM
#54
8ightScale/CJP-Car looks great, I like the "team white" paint!!
Just a note for the west coast guys, JConcepts will be out at the Cactus Classic for support. Jason and Brad will both be there for autographs, etc, haha. Seriously though, they'll be there representing.
Just a note for the west coast guys, JConcepts will be out at the Cactus Classic for support. Jason and Brad will both be there for autographs, etc, haha. Seriously though, they'll be there representing.
03-10-2007, 04:58 AM
#55
Tech Master
Andy is Jason planing on bringing spare wings etc to purchase?
03-10-2007, 08:17 AM
#57
03-10-2007, 11:10 AM
#59
Originally Posted by smac
Thanks for getting us a good look at the top and bottom of the new truck tires!! They look good from both sides!
rcdude19641-I cant say for sure, they have a LOT of stuff to take as it is. I might be able to ship them some stuff out, or convince them to take something extra, haha.
TomB-We ship direct if you have trouble finding a shop.
03-10-2007, 09:22 PM
#60
Tech Master
iTrader: (6)
Well, I went to paint an illuzion body for my T4, an the window masks fit the window outlines perfectly, and they were easy to remove. I also Put a high downforce truggy wing on my Revo, Love the wing, however the plastic washers that are included pulled right through the holes. Luckily the holes stayed the same, and the washers are fine, but needless to say I spent the rest of the afternoon Wingless. Love the way it looks however, and tonight I placed the metal washers in place of the plastic. I would like to say that both pieces are of the highest quality, and am looking to get another wing soon for my truggy. as well as more jconcepts illuzion bodies...