Schumacher Corner
wasnt there supposed to be a race in daytona today? Which track is that?
Tech Elite
iTrader: (26)
Super Moderator
iTrader: (239)
send Adrian or Jason a Pm
Adrenaline was racing today
yes dawgmeat stick with the schumacher ballcups!!
yes dawgmeat stick with the schumacher ballcups!!
Tech Elite
iTrader: (26)
Nothing better than the stock ball cups...if you got a bit of play just do what AdrianM has suggested...put a bit of a plastic bag on the ball stud and then press the ballcup into the ballstud--it'll cut out a perfect piece and stick inside the cup and take the play away...if you need more add a second layer...they'll last a really long time
Tech Adept
I've been using the RPM ball cups, purple ones to match the rest of the car With the new Ti balls they are sometimes even too tight, I had to pinch them with pliers to make them loose enough.
So, if you don't like slop in the ball cups, try the RPM ones.
So, if you don't like slop in the ball cups, try the RPM ones.
Tech Champion
iTrader: (4)
Hi guys, I just had my first foam tire race on my Mi3 yesterday and I have to give props to McGoo for his setup. It was dialed! There was only two of us in the foam stock class as rubber is king of carpet down here in FL but I had a blast.
Goetz with a Podium finish in stock TC!!!! Great job man!!!
Super Moderator
iTrader: (239)
adam check your pm!!
Tech Master
iTrader: (4)
Glad to see Chris on the podium
R/C Tech Elite Member
iTrader: (37)
Congrats to Chris, Dave and all of the Shuie drivers for another podium filled weekend
I got you Marcos let me know when your coming in...
I stole 2nd this weekend also **toots own horn**
Who cares if it was sportsman stock!
Starling, get it back to me whenever bud, good job this weekend, and nice to meet you as well!
I got you Marcos let me know when your coming in...
I stole 2nd this weekend also **toots own horn**
Who cares if it was sportsman stock!
Starling, get it back to me whenever bud, good job this weekend, and nice to meet you as well!
R/C Tech Elite Member
iTrader: (37)
I'll race foam with you next time
Tech Elite
iTrader: (9)
Any advice on what to change on very cold asphalt?
I was running Mod at West London, it was around 5 degC with damp in places.
During the second final things got worse as the car tried to spin mid corner on sweepers etc. I ran RP24's that were heated a lot before the race.
Nothing special in the setup, but the spinning made me a danger to other cars and it was very frustrating and inconsisitant..
Front;
40W
Med Roll Bar
310gf/mm Springs
1mm RC's
Rear;
35W
Thin Roll Bar
250gf/mm Springs
2mm & 2.5mm RC's
Tried moving the rear shocks in and out, in was the worst!
Thanks
Skiddins
I was running Mod at West London, it was around 5 degC with damp in places.
During the second final things got worse as the car tried to spin mid corner on sweepers etc. I ran RP24's that were heated a lot before the race.
Nothing special in the setup, but the spinning made me a danger to other cars and it was very frustrating and inconsisitant..
Front;
40W
Med Roll Bar
310gf/mm Springs
1mm RC's
Rear;
35W
Thin Roll Bar
250gf/mm Springs
2mm & 2.5mm RC's
Tried moving the rear shocks in and out, in was the worst!
Thanks
Skiddins
try dropping some shims in at the pivot blocks to lower your rear arms down
best bet is probobly to lower your rear roll center or put 45wt in the front
best bet is probobly to lower your rear roll center or put 45wt in the front