mjk1210

iTrader: (9)

same here. it will wear away pretty quick too.
i found you also need to notch out the corners of the rear hanger just a little bit to "square off" where it sits on the chassis. otherwise the rear hanger doesn't quite sit all the way down and the trans case isn't flush to the chassis. Just a quick buz with a dremel or a couple passes with a file will get it done.

...and yes, even on clay, med to high bite, removing the piece makes a big difference. I will probably only put it back when running full slicks or if I race on carpet again.

BentKa

Video from Malin's C-main Leg 1 in 4WD modified buggy @ the 2014 DHI-CUP in Denmark this weekend.

She qualified as #4 on the grid for this C-main (Finals A through F).

Juraj Hudy, Mr. Xray himself is on start #1 in this C-main.

She ended up taking 3rd place in this 1st leg with Juraj Hudy finishing in 6th spot.

This gave her a 3rd, 1st and 2nd for the 3 finals and a combined win in the C-main.

She drives the white/pink/light blue Xray XB4.

If you are watching this from an iPhone or iPad press the blue banner on top.

+ YouTube Video

Her setup:
Xray XB4 '14 4WD
Orca Vritra VXX speed controller
Orca TX 6.5T brushless motor
Orca Infinite Ultra 90C | 6000mAh | 7.4V saddle pack battery
Hitec HS-7940TH servo
Futaba 4PKS-R with 614FF receiver
Scumacher Mini Pin Yellow front & rear
New! 4dotz front springs/900cst oil/1.8 Sway Bar
3 dotz rear springs/700cst oil/1.8 Sway bar

Bent

advpball

iTrader: (30)

CONGRATS Malin that is awesome!!!!
Hope my little girl picks it up that good. She's only 6 this march but we will start with short course this summer.

Losi57

So awesome . Great job. Congrats.

aloksatoor

iTrader: (43)

very cool BentKa!

mjk1210

iTrader: (9)

+1

BentKa

Thanks

We're on the plane now to Berlin, Germany and round #2 of the Euro Offroad Series

Bent

jhautz

iTrader: (86)

Im jealous!!! Can you be my dad.... I need a sponsor like you.

zixxer

iTrader: (61)

will durango dex410 v3 rims fit on the xray car? i am thinking of switching but i have many tires on the 14mm rims for the dingo and im hoping i dont have to buy all new wheels and tires ....thanks in advance and sorry for not searching the thread

onekiwi

iTrader: (4)

They fit but the Xray rims have a different diameter where the foams sit, the xrays are a little larger

BillyT.

iTrader: (4)

You also have to drill the centers of the DEX wheels. DEX steps down to 4mm for axle. Xb4 is 5.

But I run all of my old DEX wheels on this car.

DAF Racing

iTrader: (10)

with out looking at 256 pages; can you change the x-ray over to 12mm ?

Nitronut3

iTrader: (6)

But I wouldn't suggest it. The dingo angels are a different offset and make the car narrower

aloksatoor

iTrader: (43)

Only for the rear and its cured by the 0.75 offset hexes. I use the stock hexes to stick the rear more.

mjk1210

iTrader: (9)

rears are no problem. buy the plastic hexes for the 22sct and file the back of them flat and take off about another half mm and widen the slot where the pin fits. it doesn't take much to widen the pin slot enough. then tlr22 wheels will fit and still be the exact same width. you will know you filed off enough off the back of the plastic hex when you tighten the wheel and it doesn't feel bound up at all when you spin the wheel.

not sure about the fronts.