Xray X1 - Formula One Car
#376
#378
For the ride height on foam on the back,you can drive them off until 54 mm.
Your ride height will be 3,5 mm.
On the front you can not go smaller then 61 mm.
Ride height will be 3,5 mm.
So i think there will be a conversion for the front.
When you can lower the lower suspension arms 4-5 mm. it would be great.
It can be done very simple by using a smaller aluminium mount 376364-O
Your ride height will be 3,5 mm.
On the front you can not go smaller then 61 mm.
Ride height will be 3,5 mm.
So i think there will be a conversion for the front.
When you can lower the lower suspension arms 4-5 mm. it would be great.
It can be done very simple by using a smaller aluminium mount 376364-O
I build the front as the manual said, and there are 2mm. shims placed under the aluminium mount.
When you remove them, you can ride your foam tires of untill 57 mm. by ride height 3.5mm.
#379
Tech Master
iTrader: (1)
Put the springs on as per the manual, then mount that plastic piece which now has the springs on onto your servo.
You can now put the outer section of the servo saver on by pushing and twisting (the servo needs to be at the end of it's travel in one direction so that it's held still), once the saver is almost on on that side, twist the servo around (while still pushing on the out part) so that the servo goes to the end of it's travel in the other direction, this should now push the springs apart so the outer section can push fully home.
Does that make any sense?
You can now put the outer section of the servo saver on by pushing and twisting (the servo needs to be at the end of it's travel in one direction so that it's held still), once the saver is almost on on that side, twist the servo around (while still pushing on the out part) so that the servo goes to the end of it's travel in the other direction, this should now push the springs apart so the outer section can push fully home.
Does that make any sense?
#382
Those of you that have run the car, have you tried the battery both directions? I know my crc car it runs lengthwise, but this car allows it to go lengthwise, and transverse.
If you have tried it both ways, which did you prefer and why?
Im thinking about setting mine up with the ESC standing up on one side, so I can switch it around at the track. Just wanted some feedback if you have tried it
If you have tried it both ways, which did you prefer and why?
Im thinking about setting mine up with the ESC standing up on one side, so I can switch it around at the track. Just wanted some feedback if you have tried it
#383
Tech Rookie
Absolute Hobbyz has them as of now.
#384
Those of you that have run the car, have you tried the battery both directions? I know my crc car it runs lengthwise, but this car allows it to go lengthwise, and transverse.
If you have tried it both ways, which did you prefer and why?
Im thinking about setting mine up with the ESC standing up on one side, so I can switch it around at the track. Just wanted some feedback if you have tried it
If you have tried it both ways, which did you prefer and why?
Im thinking about setting mine up with the ESC standing up on one side, so I can switch it around at the track. Just wanted some feedback if you have tried it
Almost everyone in 1/12 runs transverse as well.
#385
Those of you that have run the car, have you tried the battery both directions? I know my crc car it runs lengthwise, but this car allows it to go lengthwise, and transverse.
If you have tried it both ways, which did you prefer and why?
Im thinking about setting mine up with the ESC standing up on one side, so I can switch it around at the track. Just wanted some feedback if you have tried it
If you have tried it both ways, which did you prefer and why?
Im thinking about setting mine up with the ESC standing up on one side, so I can switch it around at the track. Just wanted some feedback if you have tried it
They both have the battery transverse.
The car has massive steer, but was predictable.
So they liked it a lot.
No experience with in line battery yet.
One was on foam and the other on Ride rubber (ETS)
It was on carpet.
Last edited by JoJo1241; 01-07-2015 at 04:34 AM. Reason: text added
#387
#389
Tech Fanatic
iTrader: (2)
Shuan B22,
Sounds good to me. My kit is complete. just waiting for the body, wheels, and electronics to arrive in the mail.
Hey Guys,
Whats a good lipo to get for this car? You guys running 1s or 2s?
SMC is my first choice but at present, they don't have any 2s shorties in stock. I'm running a LRP x20 4.0t mod motor in mine.
Sounds good to me. My kit is complete. just waiting for the body, wheels, and electronics to arrive in the mail.
Hey Guys,
Whats a good lipo to get for this car? You guys running 1s or 2s?
SMC is my first choice but at present, they don't have any 2s shorties in stock. I'm running a LRP x20 4.0t mod motor in mine.
#390