Mugen MTX-4
#8896
only run 16 or 20% nitro
only us ninja plugs (if possible)
ninja stock pipe or novarossi 52607 pipe works best
for 16 or 20% nitro run the motor how it came the extra shim that came with the motor you add if you run 30 but if you want to run 25%nitro only run that shim and take the one thats in the motor out.
stock shim is .10 and the extra one is .15.
seal the carb neck with racer's choice air seal and then clamp the carb in.
dont take the motor apart to clean,just run and add after run oil at the end of the day when you get home and take the motor out of your car.
take the air filter off (and throw it away)put the black caps on the outlets and brush the motor clean.put new air filter on.
#8897
Tech Master
iTrader: (2)
crunch time
last 3 races of the points race.
just looking for a few setups to try at the track next week.
lower traction parking lot tract. running the x4. 3mm chassis stock springs and oils (diff also), msr clutch, yellow shoe, and lightweights. hit me up. any and all info will be tried!
setup is very close to stock settings, 138b uprights
just looking for a few setups to try at the track next week.
lower traction parking lot tract. running the x4. 3mm chassis stock springs and oils (diff also), msr clutch, yellow shoe, and lightweights. hit me up. any and all info will be tried!
setup is very close to stock settings, 138b uprights
#8898
hey guys, im in need of an engine to put into my mtx-4. i was looking at an 18 tz but from what ive heard its way too much power for a tc. im gonna be doing alot of parking lot races and ill be visiting my local track alot also. so i was looking at either the picco red dot or the 12tz. which one do you think would be the easiest to tune and stuff?
#8899
Quickest way to change front belt.
Whats the fastest way to change out the front belt on this car i've gotten great feed back from the MRX4R thread and i was wondering can you use the same technique or is it a little different, all helps appreciated thanks.
#8900
Tech Elite
iTrader: (23)
hey guys, im in need of an engine to put into my mtx-4. i was looking at an 18 tz but from what ive heard its way too much power for a tc. im gonna be doing alot of parking lot races and ill be visiting my local track alot also. so i was looking at either the picco red dot or the 12tz. which one do you think would be the easiest to tune and stuff?
BTW both OS and Ofna motor will be really easy to tune.
#8904
Tech Elite
iTrader: (2)
Sure do Enti!
Just a quick job, but as you can see it fits fine!
Just run the wide bottom bumper with the standard top bumper plate and see if you can get the short 1/8th style aluminium front body posts and you are set!
These pics were with the standard body posts still on the car!
Just a quick job, but as you can see it fits fine!
Just run the wide bottom bumper with the standard top bumper plate and see if you can get the short 1/8th style aluminium front body posts and you are set!
These pics were with the standard body posts still on the car!
#8905
This is what did for lola body & bumper. Click the attachment.
LEFT is MTX4, RIGHT is NT1
Note: I don't use front body clips to hold up the body shell, instead I let the body shell sit on top of foam bumper. You need to cut the foam bumper at some angle to match the nose of lola body.
http://www.rctech.net/forum/attachme...2&d=1184783022
LEFT is MTX4, RIGHT is NT1
Note: I don't use front body clips to hold up the body shell, instead I let the body shell sit on top of foam bumper. You need to cut the foam bumper at some angle to match the nose of lola body.
http://www.rctech.net/forum/attachme...2&d=1184783022