Kyosho FW-05R
#1381
Originally posted by ziggy12345
Change the 46t Spur to 45T = FDR from 5.24 to 5.13
Change the 39T ring gear to 40T = FDR from 5.13 to 5.00
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 5.00 to 4.82
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 4.82 to 4.66
Change the 46t Spur to 45T = FDR from 5.24 to 5.13
Change the 39T ring gear to 40T = FDR from 5.13 to 5.00
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 5.00 to 4.82
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 4.82 to 4.66
Change the 40T ring gear to 39T = FDR from 5.13 to 5.00
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 5.00 to 4.82
Change the 28T Pinion to MTX-3 29 Pinion = FDR from 4.82 to 4.66
#1382
Originally posted by ziggy12345
And if thats not enough get the Kawahara Centre conversion which changes the ring gears and bevel gears but i dont know what to (I have one on order)
And if thats not enough get the Kawahara Centre conversion which changes the ring gears and bevel gears but i dont know what to (I have one on order)
#1383
So when I get the parts I should have the car where I want it!
Kawahara Centre Conversion
Kawahara Front Conversion
3racing chasis
3 racing top deck
MTX-3 rear hubs
Cheers
Kawahara Centre Conversion
Kawahara Front Conversion
3racing chasis
3 racing top deck
MTX-3 rear hubs
Cheers
#1384
Originally posted by InitialD
I think you meant this...
Change the 40T ring gear to 39T = FDR from 5.13 to 5.00
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 5.00 to 4.82
Change the 28T Pinion to MTX-3 29 Pinion = FDR from 4.82 to 4.66
I think you meant this...
Change the 40T ring gear to 39T = FDR from 5.13 to 5.00
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 5.00 to 4.82
Change the 28T Pinion to MTX-3 29 Pinion = FDR from 4.82 to 4.66
I also edited the post as I found what the centre conversion does.
Cheers
#1385
Originally posted by ziggy12345
Front = 45 and 17
Back 46 and 17
Front = 45 and 17
Back 46 and 17
Originally posted by ziggy12345
Best option is to use centre conversion with 27 pinion = FDR 4.51
Best option is to use centre conversion with 27 pinion = FDR 4.51
1st gear (20/51) = 7.65
2nd gear (29/45) = 4.66
With the stock pinions and Kawahara ring gears;
1st gear (20/51) = 6.9
2nd gear (27/45) = 4.51
Which is cheaper and easier on spares?
#1386
Originally posted by ziggy12345
Kawahara Centre Conversion
Kawahara Front Conversion
3racing chasis
3 racing top deck
MTX-3 rear hubs
Kawahara Centre Conversion
Kawahara Front Conversion
3racing chasis
3 racing top deck
MTX-3 rear hubs
#1387
Originally posted by InitialD
That's a lot of money !
That's a lot of money !
Got any more pics of the conversion Nimo?
Cheers
#1388
Originally posted by Racing4Evo
I don't deserve this car then if no one else is having gearing issues. At my track, Revelation Raceway, CA, the car is left in the dust. I have an NSR and the highest Kyosho gearing and still the car is horrible down the straight. It's as if the belt cars have 3 speeds when you compare them to this car. My S710 blows this car out of the water( only on the straight). Now what is the point of passing someone in the infield if they are going to pass you right back on the straight?
Also,
All my engines run hotter in this car.
I don't deserve this car then if no one else is having gearing issues. At my track, Revelation Raceway, CA, the car is left in the dust. I have an NSR and the highest Kyosho gearing and still the car is horrible down the straight. It's as if the belt cars have 3 speeds when you compare them to this car. My S710 blows this car out of the water( only on the straight). Now what is the point of passing someone in the infield if they are going to pass you right back on the straight?
Also,
All my engines run hotter in this car.
#1389
gears
hi guys,
went to the track today to try a few things...short work day..
39 ring front, 40 ring rear, 22/50 , 29/45.
jp ns3 worlds (not too many of these babies around, i have 2).
kyosho pipe and header..........................
man does this car go.........our rear straight is at least 120metres long wth a sharp 90 degree bend at the end.
this car just keeps pulling........the car is twitchy at high speeds...i think due to trying a new radio as well...ex-10 helios........i blew second gear...on closer inspection i seen that the mesh wasnt 100%...out with the dremel and widened the engine mounting holes...now i got the mesh right...a quick run and no probs....now i need to work on the set-up...ran out of daylight...race day sunday......ill try a few things..
mike
went to the track today to try a few things...short work day..
39 ring front, 40 ring rear, 22/50 , 29/45.
jp ns3 worlds (not too many of these babies around, i have 2).
kyosho pipe and header..........................
man does this car go.........our rear straight is at least 120metres long wth a sharp 90 degree bend at the end.
this car just keeps pulling........the car is twitchy at high speeds...i think due to trying a new radio as well...ex-10 helios........i blew second gear...on closer inspection i seen that the mesh wasnt 100%...out with the dremel and widened the engine mounting holes...now i got the mesh right...a quick run and no probs....now i need to work on the set-up...ran out of daylight...race day sunday......ill try a few things..
mike
Last edited by mikecatts; 08-13-2010 at 02:29 PM.
#1390
Originally posted by Racing4Evo
I don't deserve this car then if no one else is having gearing issues. At my track, Revelation Raceway, CA, the car is left in the dust. I have an NSR and the highest Kyosho gearing and still the car is horrible down the straight. It's as if the belt cars have 3 speeds when you compare them to this car. My S710 blows this car out of the water( only on the straight). Now what is the point of passing someone in the infield if they are going to pass you right back on the straight?
Also,
All my engines run hotter in this car.
I don't deserve this car then if no one else is having gearing issues. At my track, Revelation Raceway, CA, the car is left in the dust. I have an NSR and the highest Kyosho gearing and still the car is horrible down the straight. It's as if the belt cars have 3 speeds when you compare them to this car. My S710 blows this car out of the water( only on the straight). Now what is the point of passing someone in the infield if they are going to pass you right back on the straight?
Also,
All my engines run hotter in this car.
Also the motors in the FW need to be set up different to other cars due to the pipe.
Try richening the bottom end and lean out the top end (it will take a while to get it right), that's what I done to my NS12 S3 and boy does it scream.
Also make sure you haven't overgeared the car (as most appear to be doing), 21/50 - 26/45 with 39 diff is plenty for the 150ft Aldershot straight.
#1391
Originally posted by NiMo
Also make sure you haven't overgeared the car (as most appear to be doing), 21/50 - 26/45 with 39 diff is plenty for the 150ft Aldershot straight.
Also make sure you haven't overgeared the car (as most appear to be doing), 21/50 - 26/45 with 39 diff is plenty for the 150ft Aldershot straight.
#1392
Re: gears
Originally posted by mikecatts
man does this car go.........our rear straight is at least 120metres long wth a sharp 90 degree bend at the end.
man does this car go.........our rear straight is at least 120metres long wth a sharp 90 degree bend at the end.
Originally posted by mikecatts
out with the dremel and widened the engine mounting holes...
out with the dremel and widened the engine mounting holes...
#1393
Super Moderator
iTrader: (239)
Originally posted by InitialD
I think you meant this...
Change the 40T ring gear to 39T = FDR from 5.13 to 5.00
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 5.00 to 4.82
Change the 28T Pinion to MTX-3 29 Pinion = FDR from 4.82 to 4.66
I think you meant this...
Change the 40T ring gear to 39T = FDR from 5.13 to 5.00
Change the 27T Pinion to MTX-3 28 Pinion = FDR from 5.00 to 4.82
Change the 28T Pinion to MTX-3 29 Pinion = FDR from 4.82 to 4.66
#1394
track
hi ther "d"
our total track length is 320 metres, i know as george and i done the curbing..(site...RRCSA ).....yes the back straight is 120 metres....120 feet...thats a miniz track....in australia we have very big, purpose built tracks. quenslands straight is about 140 metres...sydney has a front straight of about 70 metres but they have a long winding back area........melbourne back straight is huge as well with a 30degree camber comming off...very fast..
mike.
posting pics of rrcsa just after hot mix.
http://www.rrcsa.org.au/
our total track length is 320 metres, i know as george and i done the curbing..(site...RRCSA ).....yes the back straight is 120 metres....120 feet...thats a miniz track....in australia we have very big, purpose built tracks. quenslands straight is about 140 metres...sydney has a front straight of about 70 metres but they have a long winding back area........melbourne back straight is huge as well with a 30degree camber comming off...very fast..
mike.
posting pics of rrcsa just after hot mix.
http://www.rrcsa.org.au/
Last edited by mikecatts; 08-13-2010 at 02:29 PM.
#1395
Nice track