Barracuda from Alex racing
#961
Tech Champion
iTrader: (31)
Originally posted by fai
In my point of view, his "Cuda" is quite "stock" when comparing with other Cuda racers! You will agree with me after have a look with his setting sheet!
In my point of view, his "Cuda" is quite "stock" when comparing with other Cuda racers! You will agree with me after have a look with his setting sheet!
but he might have done some different mounting of the wing on the Protoform 2.0..
-Dave
#962
Ok, for us Barracuda rookies...Excel, Xenon, Product"D". Who?? and What do they do. Web addresses if any?? Looks like a good time to get on the Barracuda train....I hope they come stateside and make a good impression. Alot of guy's seem to be looking for a truly race quality car that doesn't need a huge number of hop ups to be competitive. Is Barracuda the one ??
#963
Tech Champion
iTrader: (31)
Here ya go
EXCEL home page
XENON home page
As for Product "D" Very Small company... the make about2~3 things for the Barracuda..mostly motor/shaft mout with Heatsink and 16T bevel gear..
-Dave
and yes the Barracuda...R2 is the one....
Trust me on this...
Very little is needed
XENON home page
As for Product "D" Very Small company... the make about2~3 things for the Barracuda..mostly motor/shaft mout with Heatsink and 16T bevel gear..
-Dave
and yes the Barracuda...R2 is the one....
Trust me on this...
Very little is needed
#964
Does anybody know a good translator site other than babel fish??
#967
Tech Champion
iTrader: (31)
Originally posted by JDM_DOHC_SiR
Cuda's need a little TLC on the 16T & 39T gears to make the drive train smooth and spin for a long time...
For starters..... you'll need some 400~600 grit wet dry sand paper and you'll need to spend about 3 hours just removing all of the peaks on the bevel and diff gears and buy doing this you'll be able to tell just by the gear mesh and that there is less noise too!! especially if you have a Motor/shaft mount holder ( which usually makes the drive train noisy )
But with the 400( 320 is what I use less time )
start to remove a liberal ammount of material ...say about 1mm on the 39T Diff gear ....
This should take a whole Sh!t lo@d of resistance out of the Barracudas' drive train
also a little bearing prep doesn't hurt either
Try this and let me know
BTW my cuda's on aveage can spin for about 10~14 seconds without tires !! but before all of the prep work they only spun for about 5~6 tops
-Dave
Cuda's need a little TLC on the 16T & 39T gears to make the drive train smooth and spin for a long time...
For starters..... you'll need some 400~600 grit wet dry sand paper and you'll need to spend about 3 hours just removing all of the peaks on the bevel and diff gears and buy doing this you'll be able to tell just by the gear mesh and that there is less noise too!! especially if you have a Motor/shaft mount holder ( which usually makes the drive train noisy )
But with the 400( 320 is what I use less time )
start to remove a liberal ammount of material ...say about 1mm on the 39T Diff gear ....
This should take a whole Sh!t lo@d of resistance out of the Barracudas' drive train
also a little bearing prep doesn't hurt either
Try this and let me know
BTW my cuda's on aveage can spin for about 10~14 seconds without tires !! but before all of the prep work they only spun for about 5~6 tops
-Dave
#969
Tech Adept
Speed Tech RC
Hey everyone! Look on Speed Tech RC! Steve's gonna carry the Barracuda R2 soon!
#970
Tech Master
Originally posted by fai
HeHe... Although I'm in HK side, I haven't been there for a long time... I think drop him a call will be OK instead of going there...
HeHe... Although I'm in HK side, I haven't been there for a long time... I think drop him a call will be OK instead of going there...
#972
sweet
alex cars in the states will be awesome !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
#973
Tech Champion
iTrader: (31)
Post Your Barracuda Set up's
Hey all.. if you have a "HOT" setup for the Cuda.....Lets start to post them here. because I think that there will be a lot more Users this year... ..just a gut felling
-Dave
Also make sure to tell what Mod's you have on your "Cuda" . I.E. PAL arm coversion ect ect..
-Dave
-Dave
Also make sure to tell what Mod's you have on your "Cuda" . I.E. PAL arm coversion ect ect..
-Dave
#974
how is the handling on a Barracada?
say compared to a TB Evo's and TC3's?
have been thinking of getting one, but would like to sell my TB Evo II first.
say compared to a TB Evo's and TC3's?
have been thinking of getting one, but would like to sell my TB Evo II first.
Last edited by racer; 02-26-2003 at 05:55 PM.