1/10 R/C F1's...Pics, Discussions, Whatever...
#2387
Tech Champion
iTrader: (15)
2011 UF1 season will start this Saturday at West Australian Coast Grand Prix...
8 races , 8 tracks, 1 race per month, 1 2011 UF1 Champion...
For details, check out:
http://www.charleslightfoot.com/UF1/UF1_home.html
8 races , 8 tracks, 1 race per month, 1 2011 UF1 Champion...
For details, check out:
http://www.charleslightfoot.com/UF1/UF1_home.html
#2388
http://www.tamiya.com/english/rc/rcm...f103_anniv.pdf
http://www.tamiya.com/english/rc/rcmanual/f104pro.pdf
#2389
Tech Initiate
#2390
Tech Champion
iTrader: (30)
2011 UF1 season will start this Saturday at West Australian Coast Grand Prix...
8 races , 8 tracks, 1 race per month, 1 2011 UF1 Champion...
For details, check out:
http://www.charleslightfoot.com/UF1/UF1_home.html
8 races , 8 tracks, 1 race per month, 1 2011 UF1 Champion...
For details, check out:
http://www.charleslightfoot.com/UF1/UF1_home.html
#2391
#2392
Tech Addict
iTrader: (20)
Here are the manuals for both F103 & F104.
http://www.tamiya.com/english/rc/rcm...f103_anniv.pdf
http://www.tamiya.com/english/rc/rcmanual/f104pro.pdf
http://www.tamiya.com/english/rc/rcm...f103_anniv.pdf
http://www.tamiya.com/english/rc/rcmanual/f104pro.pdf
#2396
Is the other Red Bull the Mark Webber car? This one looks great. What kind of body did you use for this one?? How did you manfacture the spoiler/wing on the rear end of the body?? That just looks awesome.
Hope you understand what I mean??
Hope you understand what I mean??
#2397
Tech Fanatic
iTrader: (14)
thanks for the comment. the body is just the Tamiya F60 body. The 'Shark Fin' comes with the body kit. I used D Drive decals for most part except the front wings which I used a Deep Blue vinyl decal to get as close as possible to the body colour, which I used Tamiya PS59.
#2398
Been burning up a lot of silvercans as of late (water and air break in).
I am at a 47.25mm roll out on a foam/high grip carpet track.
I am running a fan and using a heatsink motor plate.
Thought it was my esc (gtx) but I just went to a fx pro
and burnt one up last night. I am actually a bit lower
rollout than most of my fellow racers (fast guys are @48-50mm)
and they seem to be holding up better.
My car is free (all bearings check out).
I would think that I was over geared but a few drivers are smoking
me down the straight.
What else to try?Could a cheap lipo cause problems?
Beginning to think it's my driving style.
I am at a 47.25mm roll out on a foam/high grip carpet track.
I am running a fan and using a heatsink motor plate.
Thought it was my esc (gtx) but I just went to a fx pro
and burnt one up last night. I am actually a bit lower
rollout than most of my fellow racers (fast guys are @48-50mm)
and they seem to be holding up better.
My car is free (all bearings check out).
I would think that I was over geared but a few drivers are smoking
me down the straight.
What else to try?Could a cheap lipo cause problems?
Beginning to think it's my driving style.
#2399
thanks for the comment. the body is just the Tamiya F60 body. The 'Shark Fin' comes with the body kit. I used D Drive decals for most part except the front wings which I used a Deep Blue vinyl decal to get as close as possible to the body colour, which I used Tamiya PS59.
I definitly gonna buy that F104 ferrari kit. Do you know if the Shark fin also comes with the Mclaren kit??
THANKS AGAIN