Kyosho Ultima RB6 & RB6.6 Car Thread
|
|||
#9706
Just got the new mm rf and rr hangers, was wondering if I run front d and rear d what would that do to the buggy?
#9707
Tech Master
iTrader: (90)
B-B was popular at first and it seems JPT's latest setup has D inside so the bushings are reversed. It's 4 screws.... see what works for your setup.
Last edited by Kuya_Kimo; 02-05-2014 at 06:42 AM.
#9708
Tech Regular
#9709
http://www.exotekracing.com/b4-t4-sc...spur-gear-hub/
Use with Avid top shaft.
Use with Avid top shaft.
Glenn
#9710
Tech Adept
iTrader: (3)
Can you or someone please post pic of how to get exotek eliminator to work with avid topshaft. Because i have both pieces and cant get it to fit. The exotek shaft that sticks out with the oval cutout is far too wide and sloppy to sit stable on the avid. I may be missing something, so not sure. Many thanks
Glenn
Glenn
Hi Sir,
All our testing have been on the stock factory team equipment so no feedback on the Triad aftermarket sorry.
Could you let me know how it goes? If not compatible then you are welcome to send the parts back.
The good news is the RB6 spur mount should be in stock here in March.
Thanks for your support,
Mike Rydwell
EXOTEK
3830 Oceanic Dr
Oceanside, CA 92056 USA
#9712
Ne1 have a pic of which screws to remove, on the motor guard to ad more flex?
#9713
They are the 2 3x8 flathead screws on the bottom of the chassis that hold down the center bulkhead.
#9714
Dum question Would a #53 drill bit 1.51mm ,is that what they are using for the 1.5 holes
#9715
I use precision twist C50R10PM drill set and i bought a metric drill gage in case the smaller bits get mixed up by accident. I got it on amazon and the gage was from a local machine shop supply. And then i use general tools pin vise, the one w the big black handle
#9716
I emailed Exotek to find out if they were designed for the Avid top shaft and here is what they said:
Hi Sir,
All our testing have been on the stock factory team equipment so no feedback on the Triad aftermarket sorry.
Could you let me know how it goes? If not compatible then you are welcome to send the parts back.
The good news is the RB6 spur mount should be in stock here in March.
Thanks for your support,
Mike Rydwell
EXOTEK
3830 Oceanic Dr
Oceanside, CA 92056 USA
Hi Sir,
All our testing have been on the stock factory team equipment so no feedback on the Triad aftermarket sorry.
Could you let me know how it goes? If not compatible then you are welcome to send the parts back.
The good news is the RB6 spur mount should be in stock here in March.
Thanks for your support,
Mike Rydwell
EXOTEK
3830 Oceanic Dr
Oceanside, CA 92056 USA
Sweet. Thanks for inquiring. I saw someone at the track w speedys eliminator (i think). And it looked sweet
#9717
Tech Elite
iTrader: (27)
For you guys running mid motor and want to push the battery back further, I did this in about 15 min using the stock chassis and a piece of scrap metal. I did have to drill 2 counter sunk holes in the chassis for the placement of the front battery stop and 2 holes through the rear post dealies for the metal to go across the rear for the battery to rest against.
#9718
Hi Everybody,
I just install the Avid HD Long Rear Axle and nut, i have the feeling that the Kyosho Rim touch the bearing of the hub after tightened the wheel nut.
It looks not as free as with original Kyosho Axel and nut.
Anybody facing the same problem? Do i do something wrong? Any feedback will be highly appreciated.
Ciao,
I just install the Avid HD Long Rear Axle and nut, i have the feeling that the Kyosho Rim touch the bearing of the hub after tightened the wheel nut.
It looks not as free as with original Kyosho Axel and nut.
Anybody facing the same problem? Do i do something wrong? Any feedback will be highly appreciated.
Ciao,
#9719
Hi Everybody,
I just install the Avid HD Long Rear Axle and nut, i have the feeling that the Kyosho Rim touch the bearing of the hub after tightened the wheel nut.
It looks not as free as with original Kyosho Axel and nut.
Anybody facing the same problem? Do i do something wrong? Any feedback will be highly appreciated.
Ciao,
I just install the Avid HD Long Rear Axle and nut, i have the feeling that the Kyosho Rim touch the bearing of the hub after tightened the wheel nut.
It looks not as free as with original Kyosho Axel and nut.
Anybody facing the same problem? Do i do something wrong? Any feedback will be highly appreciated.
Ciao,
'In order to use the stock RB6 rear wheels, you will need drill them out to fit over the larger axle. Avid recommends a body reamer from the inside and it will do the job nicely. AVID HD Long Axles can only be used with AVID HD Rear Hex Adapters.'
#9720
Cool i may have look in to that stuff. I found the drill bit, but I just wanted to make sure it was the right one. I normally just turn the dremel by hand with and leave it turned off.