R/C Tech Forums
0 2023/12/05 04:59:22
0 2023/12/05 04:59:10
0 2023/12/05 04:58:57
0 2023/11/10 16:46:34
0 2023/09/05 12:44:32
We'll just put a spacer between the brace and dampers to ensure they stay in place.
We'll just put a spacer between the brace and dampers to ensure they stay in place.
0 2023/06/17 04:43:56
I don't get mine until this Sunday, so I can't comment further on the tolerance yet.
I don't get mine until this Sunday, so I can't comment further on the tolerance yet.
0 2023/06/17 04:43:42
Gonna try this when indoor season starts. Solid steel. Tight tolerances.
Gonna try this when indoor season starts. Solid steel. Tight tolerances.
0 2023/06/16 18:39:28
0 2023/04/12 12:18:41
0 2023/03/22 14:22:00
Love this sloped plastic bumper... best bumper ever for a 12th scale.
Love this sloped plastic bumper... best bumper ever for a 12th scale.
0 2023/03/20 15:27:50
This chassis is fantastic for the GT12-R class. Pictured is 70/70 easy peasy lemon squeezy. Ball diff, reactive castor front end. Perfect for the class.
This chassis is fantastic for the GT12-R class. Pictured is 70/70 easy peasy lemon squeezy. Ball diff, reactive castor front end. Perfect for the class.
0 2023/03/20 14:49:18
0 2023/03/02 07:49:00
Looks like very robust caster adjustment (front and rear) by sliding the red upper bulkheads fore and aft (shims to set the position circled in blue).
Looks like very robust caster adjustment (front and rear) by sliding the red upper bulkheads fore and aft (shims to set the position circled in blue).
0 2023/02/27 08:42:33
0 2023/02/27 04:55:40
Driveshaft broke just putting it together 😭. Just crumbled while putting the set screw in 😭
Driveshaft broke just putting it together 😭. Just crumbled while putting the set screw in 😭
0 2023/02/17 15:39:44
I glued the plastic hinge pin eccentric bushings in... otherwise it's really hard to ream them properly. The end result is perfectly free & slop free arm movement.
I glued the plastic hinge pin eccentric bushings in... otherwise it's really hard to ream them properly. The end result is perfectly free & slop free arm movement.
0 2023/02/11 19:19:26
0 2023/02/11 13:02:57
0 2023/02/11 13:02:38
Literally 3 years after I started building a GT12-R car, she's finally gonna hit the track :)
Literally 3 years after I started building a GT12-R car, she's finally gonna hit the track :)
0 2023/02/11 13:01:11
0 2023/02/09 07:44:47
0 2023/02/09 07:39:46
0 2023/02/09 07:39:37
Hmm, this is strange. This red spacer would have to be glued in place in order to do it's job... you can literally push the bearing on this side all the way through and out the other end.
Hmm, this is strange. This red spacer would have to be glued in place in order to do it's job... you can literally push the bearing on this side all the way through and out the other end.
0 2023/02/08 10:13:00
0 2023/02/06 17:24:27
0 2023/02/06 16:59:31
0 2023/02/06 09:16:14
The Agata body needs very tall body down stops which makes them prone to breakage so I cut some 2.5mm carbon fiber rod to 30mm. Tips are dommed with fine sand paper.
The Agata body needs very tall body down stops which makes them prone to breakage so I cut some 2.5mm carbon fiber rod to 30mm. Tips are dommed with fine sand paper.
0 2023/01/18 16:48:24
Weight distribution is improved with the weight needed to make min under the receiver now, plus the fan and wiring more concentrated in the front section now. The car was still behaving as Felix described last Sunday "over gripping" so I'm going to try more of his setup posted in this thread.
Weight distribution is improved with the weight needed to make min under the receiver now, plus the fan and wiring more concentrated in the front section now. The car was still behaving as Felix described last Sunday "over gripping" so I'm going to try more of his setup posted in this thread.
0 2023/01/17 12:31:35
A nifty place to run an antenna if you need to like I do. Also running the fan in this location seems to work quite well on the USGT motor.
A nifty place to run an antenna if you need to like I do. Also running the fan in this location seems to work quite well on the USGT motor.
0 2023/01/17 12:26:31
0 2023/01/17 12:24:56
With 0.5mm shims to raise the diff.
With 0.5mm shims to raise the diff.
0 2023/01/12 05:15:53
0 2023/01/12 05:14:10
0 2023/01/09 14:56:36
0 2023/01/08 20:41:55
0 2023/01/05 17:54:17
I actually thought the Agata and associated bumper extension might get me closer to 50/50 front to rear balance LOL.
I actually thought the Agata and associated bumper extension might get me closer to 50/50 front to rear balance LOL.
0 2023/01/05 17:53:51
0 2023/01/04 13:16:48
First race is this Sunday - finally!
First race is this Sunday - finally!
0 2023/01/04 13:16:34
My fan almost went up in smoke due to being too close to the motor (stopped it completely in some rotor positions)... even with a 5mm spacer, the fan rpm varies depending on rotor position.
My fan almost went up in smoke due to being too close to the motor (stopped it completely in some rotor positions)... even with a 5mm spacer, the fan rpm varies depending on rotor position.
0 2023/01/03 09:45:15
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences | Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.