wilmington ohio I-71 exit 45 offroad track
#1186
Shannon, I think we're going to have a few out there. I ended up picking up the TEN-SCTE we were looking at Friday (along with a slew of parts and a servo... still need to get an ESC, motor and batts). It's in pieces now. Well built and I can't wait to slap some SS City blocks on it and see how it does. I promised myself and the fiancee that I've bought all the cars I'm getting for this season at this point. One left at the shop as of yesterday.
At this rate, the TEN will be runnable before the DNX408, I'm waiting on a clutch for it and have spring sets en route.
Now if we could just get some cooperative weather!
At this rate, the TEN will be runnable before the DNX408, I'm waiting on a clutch for it and have spring sets en route.
Now if we could just get some cooperative weather!
#1187
Tech Addict
iTrader: (38)
4wd SC
I will have to smuggle mine into my collection. New radio or another car HMMM which one to pick from. I know it's on my radar now i just need to round up another speedo, servo etc. and associated needs to come out with front floating axles for the 2wd model so we don't have to carry so many different rims
ATTENTION AE driver***** Pass along to the higers above***** MAKE THE RIMS INNERCHANGEABLE from the 2wd SC10 and the 4WD SC10 Speciall Emphasis To those local sponser AE Driver that frequent CCRCR! The Racer want it build it!! LOLOLOLOL
And no I don't want the proline kit where I have to run special offset rims!!!
Pfunk I was keeping tabs on the heated thread your where in I would like to put those parts on my SC10 just to see if there is an issue but I followed what you where saying!!!
ATTENTION AE driver***** Pass along to the higers above***** MAKE THE RIMS INNERCHANGEABLE from the 2wd SC10 and the 4WD SC10 Speciall Emphasis To those local sponser AE Driver that frequent CCRCR! The Racer want it build it!! LOLOLOLOL
And no I don't want the proline kit where I have to run special offset rims!!!
Pfunk I was keeping tabs on the heated thread your where in I would like to put those parts on my SC10 just to see if there is an issue but I followed what you where saying!!!
#1188
Tech Regular
iTrader: (10)
That whole thing was a mess.. I know the rears are an issue because i tried it myself.. don't know about the front though...
And as far as offset rims.. the protrac hexes make it so the 4x4 and 2wd use the same rims.. the kit rims for 4x4 and protrac are the same. I already bought the hexes for 2wd and am waiting for jconcepts to release their 4x4 rims so I can buy about 12 pair and reglue all my tires.
Last edited by pfunk66; 03-07-2011 at 06:49 PM.
#1189
Tech Elite
iTrader: (10)
Join Date: Nov 2004
Location: Norwood, OH...and CCRCR and The OhioRCFactory
Posts: 2,974
Trader Rating: 10 (100%+)
nevermind, Matt beat me to it.
#1190
Tech Addict
iTrader: (5)
Dylan, what gave you that impression? Was it the running across the store and jumping up to grab the box? Should have a BUNCH of parts coming Wednesday so I can start putting it back together; I'm digging it so far.
Eric is going to get one too, after I get mine put together and show it to him.
I'm just glad Tekin and GP aren't letting me down, 5th Tekin system... 5th Tekin item that had to be backordered and waited on. Hoping it comes in the next two weeks, I'd like to have it done and together before April.
Eric is going to get one too, after I get mine put together and show it to him.
I'm just glad Tekin and GP aren't letting me down, 5th Tekin system... 5th Tekin item that had to be backordered and waited on. Hoping it comes in the next two weeks, I'd like to have it done and together before April.
#1192
Tech Addict
iTrader: (5)
No, not another ESC programming software, NOOOOOOO! Hahaha. I'm just amused that the Tekin stuff I want is always on BO. The Novak stuff for the 4x4s has been pretty popular, and honestly it looks pretty good, I'm just so familiar with Hotwire anymore that it makes stuff easier for me. Plus the Novak stuff doesn't look as cool Eric has been bugging me to use an MMP too.
#1193
Tech Elite
iTrader: (10)
Join Date: Nov 2004
Location: Norwood, OH...and CCRCR and The OhioRCFactory
Posts: 2,974
Trader Rating: 10 (100%+)
Hey, Adam...found you another ESC. It'll match your shocks.
Oddly enough, it, too, is on backorder.
Oddly enough, it, too, is on backorder.
#1194
It says the best esc in china for a REASON.. hahahaha
#1195
No, not another ESC programming software, NOOOOOOO! Hahaha. I'm just amused that the Tekin stuff I want is always on BO. The Novak stuff for the 4x4s has been pretty popular, and honestly it looks pretty good, I'm just so familiar with Hotwire anymore that it makes stuff easier for me. Plus the Novak stuff doesn't look as cool Eric has been bugging me to use an MMP too.
#1197
Put your glasses on. I see it..
#1199
Tech Fanatic
iTrader: (1)
Guys, I am so smitten with the Losi that I've decided to part with the SC10
Here's what I've got.
Nothing is broken, truck is solid.
Standard SC10 with
25 degree front hubs
RPM front Bumper and standard front bumper
Factory Team rear toe-bar set (3.5 degree installed)
1.5 degree integy hubs (in packag uninstalled)
factory team titanium camber links (in package uninstalled)
standard and factory team (red front, gray rear) springs
Factory Team Motor Plate
4 KMC mounted Enduro tires (full tread)
4 KMC mounted Caliber tires (full tread)
2 KMC mounter rear Double Dees (full tread)
No electronics, add your own Tekin, Mamba or whatever
Priced to GO!
$225
Here's what I've got.
Nothing is broken, truck is solid.
Standard SC10 with
25 degree front hubs
RPM front Bumper and standard front bumper
Factory Team rear toe-bar set (3.5 degree installed)
1.5 degree integy hubs (in packag uninstalled)
factory team titanium camber links (in package uninstalled)
standard and factory team (red front, gray rear) springs
Factory Team Motor Plate
4 KMC mounted Enduro tires (full tread)
4 KMC mounted Caliber tires (full tread)
2 KMC mounter rear Double Dees (full tread)
No electronics, add your own Tekin, Mamba or whatever
Priced to GO!
$225