Losi 8ight building and setup
#7816
AKA IBeams best tire I have run so far.
#7817
Tech Elite
iTrader: (22)
I stripped down my shocks on my race roller today as I am wanting to change the piston and stipped the screw head trying to get the screw off I read in the manual that it has been loctited on I was just going to use a dremel to get it off but what is usually the best way to undo them? By putting pliers over the shaft with a rag?
#7819
Has anyone tried the Dragon Racing CNC chassis for the 8ight? I'm in need of a new chassis and have seen these on ebay.
I'm sure the Losi Stock CNC and Tuned flex chassis will be better in quality. I mean, "you get what you pay for" My main question is for anyone who has tried or seen the Dragon Racing chassis:
Were there any major problems with it?
I'm sure the Losi Stock CNC and Tuned flex chassis will be better in quality. I mean, "you get what you pay for" My main question is for anyone who has tried or seen the Dragon Racing chassis:
Were there any major problems with it?
#7820
Tech Adept
Has anyone tried the Dragon Racing CNC chassis for the 8ight? I'm in need of a new chassis and have seen these on ebay.
I'm sure the Losi Stock CNC and Tuned flex chassis will be better in quality. I mean, "you get what you pay for" My main question is for anyone who has tried or seen the Dragon Racing chassis:
Were there any major problems with it?
I'm sure the Losi Stock CNC and Tuned flex chassis will be better in quality. I mean, "you get what you pay for" My main question is for anyone who has tried or seen the Dragon Racing chassis:
Were there any major problems with it?
#7821
Tech Master
iTrader: (1)
Has anyone tried the Dragon Racing CNC chassis for the 8ight? I'm in need of a new chassis and have seen these on ebay.
I'm sure the Losi Stock CNC and Tuned flex chassis will be better in quality. I mean, "you get what you pay for" My main question is for anyone who has tried or seen the Dragon Racing chassis:
Were there any major problems with it?
I'm sure the Losi Stock CNC and Tuned flex chassis will be better in quality. I mean, "you get what you pay for" My main question is for anyone who has tried or seen the Dragon Racing chassis:
Were there any major problems with it?
#7822
locktited shock shafts
I stripped down my shocks on my race roller today as I am wanting to change the piston and stipped the screw head trying to get the screw off I read in the manual that it has been loctited on I was just going to use a dremel to get it off but what is usually the best way to undo them? By putting pliers over the shaft with a rag?
usually the heat will soften the locktite so you can remove it
#7824
Tech Apprentice
Any camber hole you change to will require a link adjustment. Its just to drastic of a change. "your tires will have way to much camber - or + " The lower the inner hole, the more you increase roll center. The more parallel the link and arms are with one another the car will have less roll. Try just running the stock setup with less camber. Keep in mind too, the further you mount them inboard the more camber you will have when the suspension is traveling. Sure you dont have a right hand turn you always get on the gas in?
#7826
Tech Champion
iTrader: (264)
Camber links are an confusing adjustment.
Think of it like this:
The shorter the link the less side bite (traction sideways)
The longer the link the more side bite (traction sideways)
The more parallel the link to the lower arms the less roll the car will have.
The more angled down the inner is the more roll the car will have.
Any time you make a change in length you must reset your static camber.
A shorter link like in most of the setups will allow the car to rotate through the corner and not scrub speed, then when you exit the corner the car should square itself with the front wheels and accelerate.
The longer link like you are running car do two things:
1) it can keep the rear planted in the corner and cause it to push coming out
2) it can keep the car planted in the corner then when you get on the gas to exit it can make the car spin out or continue the corner.
I would start with the easy to drive setup and adjust from there. I think the rear is set at 4A and the front at 3
Think of it like this:
The shorter the link the less side bite (traction sideways)
The longer the link the more side bite (traction sideways)
The more parallel the link to the lower arms the less roll the car will have.
The more angled down the inner is the more roll the car will have.
Any time you make a change in length you must reset your static camber.
A shorter link like in most of the setups will allow the car to rotate through the corner and not scrub speed, then when you exit the corner the car should square itself with the front wheels and accelerate.
The longer link like you are running car do two things:
1) it can keep the rear planted in the corner and cause it to push coming out
2) it can keep the car planted in the corner then when you get on the gas to exit it can make the car spin out or continue the corner.
I would start with the easy to drive setup and adjust from there. I think the rear is set at 4A and the front at 3
#7827
Is the losi 8ight worth holding on to or is it better to sell it to make way for the new buggy. I am concerned about parts being available and will it still be on the competetive edge with all the other new buggies coming out.
#7828
AE
Parts for the current Eight won't be that hard to find. Losi has always supported non current models with plenty of parts.
#7829
Ok well thats good what about the new supposed 8ight 2.0 thats coming out. The new buggy is going to solve the issues that the current 8ight has and that is definitely going to be a huge advantage over the current 8ight
#7830
is it the standard in the 4 shoe clutch to run matching opposite shoes
for example: 2 carbon and 2 aluminum on opposite sides with springs to match
i mean, that's the stock setup.
Would it give a more gradual effect if lets say, you run 4 of the same shoes with 4 different springs: lightest to hardest? or is this a bad idea?
all input/criticism is appreciated.
for example: 2 carbon and 2 aluminum on opposite sides with springs to match
i mean, that's the stock setup.
Would it give a more gradual effect if lets say, you run 4 of the same shoes with 4 different springs: lightest to hardest? or is this a bad idea?
all input/criticism is appreciated.