anthony390

batjam1 umm ya what r u talking about ''more then 4 bolts holding the diff down'' because if its under the chassis screws its 4 screws that hold the diff case on the chassis and theres 6 screws that hold the top of the diff case down is that what your talking about

(For both Tc3 and Tc4)

just got confused

anthony390

i saw some guy that has tc4 rear arms on his tc3 and i was wondering if i can also do that

if so, what do i need to do in order to equip it on

Thank you

BatJam1

We buy new tires and cut the foam down to 56-57 mm in diameter,It does 2 things :helps keep the tires from peeling and chunking,they last longer and also helps with the rollout! 26mm is the width of the tire!!!!!
And Big Daddy wanted to know if the bolt pattern is the same on the chassis of a TC3 to aTC4 Maybe the team but not the factory team!

Aries326

iTrader: (19)

Which one did you click? The manual that I got off their website is the 2001 manual with the dropp screws. PM me your gmail and I'll send you the PDF.

Aries326

iTrader: (19)

Probably the arm mounts and the new hinge pins. I know the TC4 has thicker hingepins than the TC3.

anthony390

k

[email protected]

and thanks again henry(threaded shocks and manual)


P.S on saturday youll ship it right? just checking and tell me my address so i know its right K?

Mr.Pink

iTrader: (2)

I am running a Orion RUSH motor 27x1 , and a 28Tooth pinion gear . My tires are 56mm dia.
Does anyone fore see and problems with running this gearing ?

anthony390

umm i am about to clean out my bearings and i was wondering if the RPM bearing blaster really cleanes out the bearings... oh ya i have metal shielded bearings

Thanks

tom235

the blaster works great i soak mine for a little bit then blast them
i don't do the ones on the wheels

BatJam1

i'm not sure about the hinge pins being thicker but i do know you could run the rear shock tower up front,and they make tc3 arms with 2 shock mounting holes its the newer style arms !Maybe thaTS WHAT YOU SAW!

PART #3884 front arms
Part #3885 front carbon arms
Part#3893 rear arms
Part#3894 rear carbon arms
try to get the Assciated tuning guide on CD its great

anthony390

ya i know thats what i have on my car and except tc3 i have tc4 shock towers and braces

and trust me its not that. i figured out it already its the tc3 200mm conversion

Mr.Pink

iTrader: (2)

So i ran my first packs with my Orion 27T RUSH motor and a 28Tpinion . I am kinda disapointed with the speed , i know it is a stocker motor , but my Mini Cooper M03 chassis was faster with a 540 mabuchi . I broke the motor in by running it on 2cells for 4 mins . and I ran it with 2400mah packs . How long of run times should I be getting? maybe my batts are fried . What do you think ?

graphiteman

iTrader: (4)

I think you would notice a big improvement with a newer pack of batteries (GP3300, GP3700). If your 2400's have been sitting a while, they are most likely the problem. Even a slow stocker should run circles around your mini.

RED-LINE M03

iTrader: (127)

I e-mailed AE about parts being available in the future for the TC-3.

----------------------------------------------------------------------------------------------------------------------------------

F.Y.I.

I just bought a TC3.
I am a little worried if AE is planning on discontinue parts in the
near future

I really hope not being that it is a very popular car.


Regards,
Eric

----------------------------------------------------------------------------------------------------------------------------------

Eric,
We expect to continue to sell parts for this car for a while to come!
There are still many owners who need them.



Sounds like we have nothing to worry about for a long time.

Later,
E

BatJam1

Its good to know AE gotyour back!