Hpi Pro 4
Well if youre a tower member you can get 30 dollars off on a 200+ dollar order... ultimately youre only paying 259... not bad with the free shipping...
Tech Master
iTrader: (9)
speed tech is good n cheap. i think they have the 1.1 pro4 but i'm not sure. it's US$277.99 but shipping to aus is the killer.
Originally posted by robk
the asphalt track had so much grip the arms broke!!
the asphalt track had so much grip the arms broke!!
hi
i keep gettin through CVD bones all the time coz i keep rip-ping the pin straight through the holes i was told to not make my steering as a aggressive how do i do this .
thanks
i keep gettin through CVD bones all the time coz i keep rip-ping the pin straight through the holes i was told to not make my steering as a aggressive how do i do this .
thanks
Tech Apprentice
Two choices.
1: turn down down your EPA to put less excessive load on the CVD.
2: Buy some steel UJ's and leave it the same.
You may have to adjust your setup to compensate for the loss of steering travel when you turn down the steering travel.
Jonathan
1: turn down down your EPA to put less excessive load on the CVD.
2: Buy some steel UJ's and leave it the same.
You may have to adjust your setup to compensate for the loss of steering travel when you turn down the steering travel.
Jonathan
Tech Addict
any good pro4 set-ups comming out of the snowbirds? and what are the best over-all pivot support spacers to use. 2mm......1mm...1.5mm...1/16"? thanx.
Originally posted by TRF Drive Hard
So does the track size determine what size pinion should be used along with type of motor? From what im trying to understand, it seem on a larger track, you can go large on the pinion size... but say if i use a 38t pinion on a short track, i can burn out my motor ya?
So does the track size determine what size pinion should be used along with type of motor? From what im trying to understand, it seem on a larger track, you can go large on the pinion size... but say if i use a 38t pinion on a short track, i can burn out my motor ya?
Tech Master
iTrader: (4)
Hey kingcrab,
so how was the straight carbon chassis? does it work well? how much you plan to sell? please let us know. thanks
so how was the straight carbon chassis? does it work well? how much you plan to sell? please let us know. thanks
Tech Adept
Guo Chean : I'll test it at TITC 2005 this weekend. 3 world champion (Hara, Surikarn, Rheinard) join this race. I may ask Hara about setting. Then I'll let you know how it works.
I plan to sell 200 usd for chassis + upperdeck.
I plan to sell 200 usd for chassis + upperdeck.
Tech Master
iTrader: (1)
Originally posted by Kingcrab
Guo Chean : I'll test it at TITC 2005 this weekend. 3 world champion (Hara, Surikarn, Rheinard) join this race. I may ask Hara about setting. Then I'll let you know how it works.
I plan to sell 200 usd for chassis + upperdeck.
Guo Chean : I'll test it at TITC 2005 this weekend. 3 world champion (Hara, Surikarn, Rheinard) join this race. I may ask Hara about setting. Then I'll let you know how it works.
I plan to sell 200 usd for chassis + upperdeck.
Tech Adept
I have noticed that there is a lot of play in the wheel axles.
This after running only 30 batts. Most cars have some play but not as much as on my Pro4. Anyone noticed this on their Pro4?
Is it the bearings or the MIP wheel axles?
This after running only 30 batts. Most cars have some play but not as much as on my Pro4. Anyone noticed this on their Pro4?
Is it the bearings or the MIP wheel axles?
Tech Champion
iTrader: (42)
Originally posted by moonman
I have noticed that there is a lot of play in the wheel axles.
This after running only 30 batts. Most cars have some play but not as much as on my Pro4. Anyone noticed this on their Pro4?
Is it the bearings or the MIP wheel axles?
I have noticed that there is a lot of play in the wheel axles.
This after running only 30 batts. Most cars have some play but not as much as on my Pro4. Anyone noticed this on their Pro4?
Is it the bearings or the MIP wheel axles?
---------------------
Does anyone know a site to buy the new HPI Aluminum Upper Camber link mounts or the Jet Racing Upper Inner Chamber Link Mount ?
Other then overseas sites...looking for something here in the U.S.
Tech Addict
iTrader: (29)
There seems to be a little more play than other touring cars in the front and rear hubs, but nothing to worry about.
Tech Master
iTrader: (4)
scoobydo : are you sure? that pretty expensive man how come cost so high? for the straight carbon chassis and upper deck?
Tech Master
iTrader: (4)
Sorry my message is for KingCrab