Awesomatix EP Touring Car (A700 Shaft Drive)
#5431
Tech Elite
iTrader: (9)
Are the current FFG upgrade kits shipping with C31S or C31? Is there an identifying feature that differentiates between C31S and C31? I just finished upgrading my car but there isn't very much side to side resistance.
I have another question regarding C21. Looks like I got a prototype top deck rather than the production top deck, center hole is 7mm. I have read you should run a bearing, washer and screw for this configuration. This combo allows a lot more movement than the production C21 with a 6mm hole.
I have another question regarding C21. Looks like I got a prototype top deck rather than the production top deck, center hole is 7mm. I have read you should run a bearing, washer and screw for this configuration. This combo allows a lot more movement than the production C21 with a 6mm hole.
Side to side it does feel free and this is normal due to the long leverage point even with the stiffer tube. What you will really feel with the stiffer tube is the resistance to twisting.
Kody
#5433
Tech Rookie
Damper question:
Under what conditions (e.g. track, motor) would the the asymmetric damper mode be a better choice than the factory set symmetric?
Under what conditions (e.g. track, motor) would the the asymmetric damper mode be a better choice than the factory set symmetric?
#5434
I like asymmetric for low grip asphalt. It lets the front end react and turn in more quickly, and lets the rear squat better on power without making the rear become unstable on entry or the front lose too much grip on exit.
#5435
A700 Evo USA SPEC 1/10 Electric Touring Car
hey all,
I'm in the process of pulling the trigger on the A700 Evo USA SPEC 1/10 Electric Touring Car.
Can you let me know what optional parts I should get, gears for 17.5 64p 3.50-4.0 fdr, and spares???
Thank you in advance for any help you can provide.....
I'm in the process of pulling the trigger on the A700 Evo USA SPEC 1/10 Electric Touring Car.
Can you let me know what optional parts I should get, gears for 17.5 64p 3.50-4.0 fdr, and spares???
Thank you in advance for any help you can provide.....
#5436
Tech Rookie
#5437
Tech Apprentice
iTrader: (11)
#5438
#5439
How do you guys remove P03 from AT21? I have to add some spacers under AT21...
#5440
Tech Regular
iTrader: (1)
Greetings!
Hi Oleg and all.
I would just like to ask if I were to use the asymmetric mode, do I need to set the set screw m3x4 all the way until I feel it locks or just half way through?
2nd, Regarding the shimming on AM26 to make the roll-center pretty much lower, can you provide a tip on proper shimming? I have this setting on mine (picture attached). Did I achieve what you're suggesting on your previous comment, Oleg?
I am racing on asphalt here and I think that asymmetric mode fits better + much lower roll center. It is stable and consistent but I want to push further. I'll post a feedback once I'm done testing this new set-up
Here's the track here just right beside the Formula 1 race track (Bahrain Grand Prix).
Thanks in advance. Cheers.
JC
Hi Oleg and all.
I would just like to ask if I were to use the asymmetric mode, do I need to set the set screw m3x4 all the way until I feel it locks or just half way through?
2nd, Regarding the shimming on AM26 to make the roll-center pretty much lower, can you provide a tip on proper shimming? I have this setting on mine (picture attached). Did I achieve what you're suggesting on your previous comment, Oleg?
I am racing on asphalt here and I think that asymmetric mode fits better + much lower roll center. It is stable and consistent but I want to push further. I'll post a feedback once I'm done testing this new set-up
Here's the track here just right beside the Formula 1 race track (Bahrain Grand Prix).
Thanks in advance. Cheers.
JC
#5442
Tech Fanatic
Greetings!
Hi Oleg and all.
I would just like to ask if I were to use the asymmetric mode, do I need to set the set screw m3x4 all the way until I feel it locks or just half way through?
2nd, Regarding the shimming on AM26 to make the roll-center pretty much lower, can you provide a tip on proper shimming? I have this setting on mine (picture attached). Did I achieve what you're suggesting on your previous comment, Oleg?
I am racing on asphalt here and I think that asymmetric mode fits better + much lower roll center. It is stable and consistent but I want to push further. I'll post a feedback once I'm done testing this new set-up
Here's the track here just right beside the Formula 1 race track (Bahrain Grand Prix).
Thanks in advance. Cheers.
JC
Hi Oleg and all.
I would just like to ask if I were to use the asymmetric mode, do I need to set the set screw m3x4 all the way until I feel it locks or just half way through?
2nd, Regarding the shimming on AM26 to make the roll-center pretty much lower, can you provide a tip on proper shimming? I have this setting on mine (picture attached). Did I achieve what you're suggesting on your previous comment, Oleg?
I am racing on asphalt here and I think that asymmetric mode fits better + much lower roll center. It is stable and consistent but I want to push further. I'll post a feedback once I'm done testing this new set-up
Here's the track here just right beside the Formula 1 race track (Bahrain Grand Prix).
Thanks in advance. Cheers.
JC
2. AM26 were designed for rear suspension only. And it was designed for increasing of camber gain but not for lowering of the roll center. Our team drivers didn't have the experience of using AM26 on the front suspension.
So your feedback for this will be very interesting for me.
Usually the front suspension doesn't need so big camber gain as AM26 can provide. This is due to the proper front caster provides a lot of desirable "camber gain" for the turned front wheels.
You can find the setups with AM26 on http://www.petitrc.com/reglages/awes...matixA700.html
Please see Viljami Kutvonen carpet setups 19-20.01.2013 and 27.01.2013
To get the maximum possible camber gain with AM26 you have to use AM06S and lower inner AT21S with 0 shims.
With so increased camber gain you can reduce the initial camber to 0,5-1 deg and get the increasing of the initial tire contact patch.
#5445
Tech Rookie
AM26 and EVO
Will setups using the AM26 work on an EVO? It looks like the front hole choice for 27-1-13 and 19-20.01.2013 are not possible on an EVO.