Team Corally RDX Touring Car
#2686
Tech Elite
iTrader: (30)
Originally Posted by gc2005
Wow! Stormer has it for $450. That's alot of mula. What's the difference between the UK kit and the US?
Will the UK kit work on carpet? Need a place that has it in stock at a decent price...$450 is just too much. I can't justify spending 1/2 grand on a touring car kit.
Will the UK kit work on carpet? Need a place that has it in stock at a decent price...$450 is just too much. I can't justify spending 1/2 grand on a touring car kit.
#2687
I wish i could get the RDX for $399. In Australia they are between $700 - $800.
#2689
Originally Posted by Brandon Melton
One thing I did recently that I liked alot was to take the standard piston (0.9) and drill one hole out to a .055. It was more simliar to the 1.3's but I thought it worked a bit better. Car had more steering without being twitchy.
Last edited by T1Raycer; 07-05-2005 at 07:53 PM.
#2690
Originally Posted by gc2005
Wow! Stormer has it for $450. That's alot of mula. What's the difference between the UK kit and the US?
Will the UK kit work on carpet? Need a place that has it in stock at a decent price...$450 is just too much. I can't justify spending 1/2 grand on a touring car kit.
Will the UK kit work on carpet? Need a place that has it in stock at a decent price...$450 is just too much. I can't justify spending 1/2 grand on a touring car kit.
The kit for $450 is the Carpet Spec kit.
The standard and UK kits sell for $400 to $420.
The UK kit works fine on Carpet........... Jeff Dayger nearly won the Carpet Nationals with a box stock UK kit, finished 2nd.
Jeff
#2691
Good run for the RDX at the West Virginia State Champs.
Mo Denton TQ'd and won both stock and 19-turn with his car, and I drove mine to 3rd in both classes.
Mo Denton TQ'd and won both stock and 19-turn with his car, and I drove mine to 3rd in both classes.
#2692
Tech Elite
iTrader: (9)
Ackerman aggressive set-up?
I'm running on a wide open high bite carpet track, the track has 2 sweepers begining and at the end of the 110 ft. straightaway.
with a 9x1 single going down the straight away it will have you on edge ,will the aggressive set allow you to take sweeper deeper at the entering point of the turn, I have been able to start making the turn at the end of the straight away(SOMETIMES) but I always seem to be a frog hair away from that 2x4 barrier, oh ya I'm runnin' the stock set-up
with a 9x1 single going down the straight away it will have you on edge ,will the aggressive set allow you to take sweeper deeper at the entering point of the turn, I have been able to start making the turn at the end of the straight away(SOMETIMES) but I always seem to be a frog hair away from that 2x4 barrier, oh ya I'm runnin' the stock set-up
#2693
Originally Posted by wolfman76
I wish i could get the RDX for $399. In Australia they are between $700 - $800.
The $399 is USD which compares to approx: $AUD540 plus the extra shipping costs that we have being so far away from everywhere.
I think $US399 is still pretty cheap though, considering the RDX is such a good car and comes with all the goodies ready for racing, i.e. there are very few option parts required to go competitive racing!
:-)
You guys in the States are lucky to get it for that! I talked with a guy in Japan who runs the RDX and retail Japan price is the equivalent of over $AUD1000 :-P
#2694
BACK IN STOCK
2.4mm Chassis
RDX US Carpet Spec Kits
Hauler Bags
Transmitter Bags
Aluminum Power Cases for Batteries
Aluminum Power Cases for Motors
NEW PRODUCTS
SRC1005 - Thin Rubberneck hardfoam bumper for RDX. This will allow easier use of a kydex bumper such as a BRP.
SRC1133 - Machined 3x6mm bushings for Aluminum Steering Knuckles. Slip these into your knuckles to beef up the strength on impacts. (Set of 4) - Retail $24.00
79182ST - Steel Standard Dogbones for your CVD Axles. (1 pair)
ON THE WAY
3.9mm Chassis being cut
Steel Bones being cut for use with Steel Blades
Steel Blades being cut
2.4mm Chassis
RDX US Carpet Spec Kits
Hauler Bags
Transmitter Bags
Aluminum Power Cases for Batteries
Aluminum Power Cases for Motors
NEW PRODUCTS
SRC1005 - Thin Rubberneck hardfoam bumper for RDX. This will allow easier use of a kydex bumper such as a BRP.
SRC1133 - Machined 3x6mm bushings for Aluminum Steering Knuckles. Slip these into your knuckles to beef up the strength on impacts. (Set of 4) - Retail $24.00
79182ST - Steel Standard Dogbones for your CVD Axles. (1 pair)
ON THE WAY
3.9mm Chassis being cut
Steel Bones being cut for use with Steel Blades
Steel Blades being cut
#2695
Tech Champion
iTrader: (31)
Originally Posted by CorallyUSA
BACK IN STOCK
2.4mm Chassis
RDX US Carpet Spec Kits
Hauler Bags
Transmitter Bags
Aluminum Power Cases for Batteries
Aluminum Power Cases for Motors
NEW PRODUCTS
SRC1005 - Thin Rubberneck hardfoam bumper for RDX. This will allow easier use of a kydex bumper such as a BRP.
SRC1133 - Machined 3x6mm bushings for Aluminum Steering Knuckles. Slip these into your knuckles to beef up the strength on impacts. (Set of 4) - Retail $24.00
79182ST - Steel Standard Dogbones for your CVD Axles. (1 pair)
ON THE WAY
3.9mm Chassis being cut
Steel Bones being cut for use with Steel Blades
Steel Blades being cut
2.4mm Chassis
RDX US Carpet Spec Kits
Hauler Bags
Transmitter Bags
Aluminum Power Cases for Batteries
Aluminum Power Cases for Motors
NEW PRODUCTS
SRC1005 - Thin Rubberneck hardfoam bumper for RDX. This will allow easier use of a kydex bumper such as a BRP.
SRC1133 - Machined 3x6mm bushings for Aluminum Steering Knuckles. Slip these into your knuckles to beef up the strength on impacts. (Set of 4) - Retail $24.00
79182ST - Steel Standard Dogbones for your CVD Axles. (1 pair)
ON THE WAY
3.9mm Chassis being cut
Steel Bones being cut for use with Steel Blades
Steel Blades being cut
#2697
dawgmeat do you have a pictures of your car whitout body?? want to see those blue turnbuckles??
Later!!
Later!!
#2699
thanks!!