Mugen MBX5R
#646
Will this battery: http://www.amainhobbies.com/product_...ducts_id/16279 fit inside the 5r radio box?
Yes that will fit....its tight...but itll go....Just dont FORCE the lid down if it dosent close right...wiggle it around and should find the sweet spot.
#647
For the Mugen Buggy and Truggy.
Innovative Designs Racing Concepts THC Pillow balls
Less un-sprung weight for better rough track performance.
Hard anodized/teflon coated.
Half the weight of stock.
Available at A Main and B Main Hobbies
Innovative Designs Racing Concepts THC Pillow balls
Less un-sprung weight for better rough track performance.
Hard anodized/teflon coated.
Half the weight of stock.
Available at A Main and B Main Hobbies
#648
hey mate, will they be available at carolinas rc soon??
#649
Jon has yet to place an order for them.
#651
try tony at tonyscrews he sells in bulk and just so happens to run mugens.
#653
Tech Fanatic
iTrader: (22)
dgraham225- i actually just made some of these out of 303 stainless the other night, i think i made like 30-40 of them. i can see how many i have, should have at least 20 of them. i ran them on one of my cnc lathes with a barfeeder attached, did not take very long. i even ran some smaller ones too
#657
Tech Master
iTrader: (13)
Mugen sells the countersunk washers in a 15-pack.
Part # B0408 - 4mm
Part # B0407 - 3mm
Amainhobbies has the 4mm ones in stock:
http://www.amainhobbies.com/product_...oducts_id/8561
Part # B0408 - 4mm
Part # B0407 - 3mm
Amainhobbies has the 4mm ones in stock:
http://www.amainhobbies.com/product_...oducts_id/8561
#658
Registered User
During the last 2 rounds at dartfordracetrack at the badlands challenge ive had nothing but problems,
Runaways
Dead servos
Dead batteries
Dead starterbox
etc....
Still had a good time mind thanks to the people there but it cheesed me off to be honest
Well ive taken drastic action to stop it happening ever again (fingers crossed)
Replaced the switch with deans connectors
Replaced the battery with a lipo
Replaced the servo with another ace (not in pic yet)
Replaced starterbox with nice spanky grey one
Then i needed a new shell after the runaways wrecked the other one
Cue rmv shell and i was supplied with some groovy stickers from www.Rcnut.com (aka carlos)
And the rework began....
The results are below needless to say im happy with it
Hope you like it as much as me
Runaways
Dead servos
Dead batteries
Dead starterbox
etc....
Still had a good time mind thanks to the people there but it cheesed me off to be honest
Well ive taken drastic action to stop it happening ever again (fingers crossed)
Replaced the switch with deans connectors
Replaced the battery with a lipo
Replaced the servo with another ace (not in pic yet)
Replaced starterbox with nice spanky grey one
Then i needed a new shell after the runaways wrecked the other one
Cue rmv shell and i was supplied with some groovy stickers from www.Rcnut.com (aka carlos)
And the rework began....
The results are below needless to say im happy with it
Hope you like it as much as me
#659
Tech Legend
iTrader: (294)
Heck, I got so frustrated with nitro I sold all my nitro stuff.
Did pick up a 1/8 scale MBX5 brushless though!
Question: I am removing some old parts, and need advice on the best way to get stuck set screws (not stripped) out of the axles. thinking I will have to heat them up again, especially if the previous owner had red loctited them.
Did pick up a 1/8 scale MBX5 brushless though!
Question: I am removing some old parts, and need advice on the best way to get stuck set screws (not stripped) out of the axles. thinking I will have to heat them up again, especially if the previous owner had red loctited them.