GM Brushless
#1111
use the 13.5 setup I posted and just change the following:
reserved: 89 -> 81
switchpointrpm: 10000 -> 15000
and you should be set
gearing between 5,5 and 7,5 depending on the track
reserved: 89 -> 81
switchpointrpm: 10000 -> 15000
and you should be set
gearing between 5,5 and 7,5 depending on the track
#1112
Thankyou
#1113
Tech Regular
Hi
Going to run 1s lipo in 12
What would you set the esc to at present for 4cell i have been on prog3 but what else would you change on rhe settings to compensatw for the lower voltage going to run 4 turn in it
Also if running sensorless what timing would you use?
Thanks
Going to run 1s lipo in 12
What would you set the esc to at present for 4cell i have been on prog3 but what else would you change on rhe settings to compensatw for the lower voltage going to run 4 turn in it
Also if running sensorless what timing would you use?
Thanks
#1114
hi guys
is gm90 capable to do what gm120 does?
and is it as strong as gm120 @ stock 13.5T?
Are they comes with latest software or not?
cheers
is gm90 capable to do what gm120 does?
and is it as strong as gm120 @ stock 13.5T?
Are they comes with latest software or not?
cheers
#1115
Tech Initiate
What do the RESERVED settings actually do?
when you take it from say 88 to 81?? what temp it shuts down at?? change lipo mode?
and RESERVED 2? what do they actually do??
when you take it from say 88 to 81?? what temp it shuts down at?? change lipo mode?
and RESERVED 2? what do they actually do??
Last edited by pee vee; 11-07-2009 at 01:24 AM.
#1116
Tech Apprentice
#1117
ok thanks martin for your soldering advice, i will probably send it in and get the new firmware and wires done at the same time.any idea of how much and how long it takes?? plummers
#1118
Tech Rookie
martin i wonder if you can help
Customer has a brand new 120 with version 7.2 software.
running standard mode 8 from factory, set using tx as customer has no pc
this has melted 3 motors, gm, novak and nosram
the motors are running at approx 100deg c after only 2 mins!
i cannot see what could be causing this ?
i will download settings and send gda when i have gda, but what could cause this?
i run same speedo same geraing and motor at club and mine run fine and only 60c.
Many Thanks
Richard Baker
Customer has a brand new 120 with version 7.2 software.
running standard mode 8 from factory, set using tx as customer has no pc
this has melted 3 motors, gm, novak and nosram
the motors are running at approx 100deg c after only 2 mins!
i cannot see what could be causing this ?
i will download settings and send gda when i have gda, but what could cause this?
i run same speedo same geraing and motor at club and mine run fine and only 60c.
Many Thanks
Richard Baker
#1119
martin i wonder if you can help
Customer has a brand new 120 with version 7.2 software.
running standard mode 8 from factory, set using tx as customer has no pc
this has melted 3 motors, gm, novak and nosram
the motors are running at approx 100deg c after only 2 mins!
i cannot see what could be causing this ?
i will download settings and send gda when i have gda, but what could cause this?
i run same speedo same geraing and motor at club and mine run fine and only 60c.
Many Thanks
Richard Baker
Customer has a brand new 120 with version 7.2 software.
running standard mode 8 from factory, set using tx as customer has no pc
this has melted 3 motors, gm, novak and nosram
the motors are running at approx 100deg c after only 2 mins!
i cannot see what could be causing this ?
i will download settings and send gda when i have gda, but what could cause this?
i run same speedo same geraing and motor at club and mine run fine and only 60c.
Many Thanks
Richard Baker
#1120
I cannot really tell you how long it takes but I'd say no longer than 2 weeks
martin i wonder if you can help
Customer has a brand new 120 with version 7.2 software.
running standard mode 8 from factory, set using tx as customer has no pc
this has melted 3 motors, gm, novak and nosram
the motors are running at approx 100deg c after only 2 mins!
i cannot see what could be causing this ?
i will download settings and send gda when i have gda, but what could cause this?
i run same speedo same geraing and motor at club and mine run fine and only 60c.
Many Thanks
Richard Baker
Customer has a brand new 120 with version 7.2 software.
running standard mode 8 from factory, set using tx as customer has no pc
this has melted 3 motors, gm, novak and nosram
the motors are running at approx 100deg c after only 2 mins!
i cannot see what could be causing this ?
i will download settings and send gda when i have gda, but what could cause this?
i run same speedo same geraing and motor at club and mine run fine and only 60c.
Many Thanks
Richard Baker
which winds/batteries are we talking about?
#1121
Tech Initiate
Martin do you have any idea when
GM releases is second generation Genius 120?
GM releases is second generation Genius 120?
#1122
Hi
Going to run 1s lipo in 12
What would you set the esc to at present for 4cell i have been on prog3 but what else would you change on rhe settings to compensatw for the lower voltage going to run 4 turn in it
Also if running sensorless what timing would you use?
Thanks
Going to run 1s lipo in 12
What would you set the esc to at present for 4cell i have been on prog3 but what else would you change on rhe settings to compensatw for the lower voltage going to run 4 turn in it
Also if running sensorless what timing would you use?
Thanks
"timing with sensors" = 0°
then just use a 4T sensorless and you are good
there'S a question mark next to reserved in the pc software
if you click on that you see ALL extra function you can en- or disable
#1123
Tech Initiate
#1124
Hello pips
i need some help please...
ive bought a GM120 to put on my RC10 B4 (TT), to take of my ezrun...
i´me run whit a GM evo3 7,5T motor, and 25C hardcase lipo 2S
next week i´ve a indoor and i like to try my new esc GM120...
i need some help to choose the best mode:
i choose mode 4, and i work to a soft curve, soft start 0,50s, brake max 90 and fuul bake 90...
do you have any tips for me?
sorry for my bad english
Bruno, from Portugal
i need some help please...
ive bought a GM120 to put on my RC10 B4 (TT), to take of my ezrun...
i´me run whit a GM evo3 7,5T motor, and 25C hardcase lipo 2S
next week i´ve a indoor and i like to try my new esc GM120...
i need some help to choose the best mode:
i choose mode 4, and i work to a soft curve, soft start 0,50s, brake max 90 and fuul bake 90...
do you have any tips for me?
sorry for my bad english
Bruno, from Portugal
#1125
Tech Fanatic
iTrader: (1)
Update für Genius 80, 95, 50, 85, 100 V7.7:
Info from Ralf:
Update für Genius 80, 95, 50, 85, 100 V7.7:
Der Fehler in der V7.6 wurde gefunden.
Bei der V7.7 ist jetzt auch Rückwärtsfahrt mit Sensoren möglich.
-------
url: http://forum.gm-racing.de/forum/topi...5-100-v77.aspx
-------
Good news from GM!
So we can update to new version if we want reverse with sensors
Regards!
m.
Update für Genius 80, 95, 50, 85, 100 V7.7:
Der Fehler in der V7.6 wurde gefunden.
Bei der V7.7 ist jetzt auch Rückwärtsfahrt mit Sensoren möglich.
-------
url: http://forum.gm-racing.de/forum/topi...5-100-v77.aspx
-------
Good news from GM!
So we can update to new version if we want reverse with sensors
Regards!
m.