Team Losi JRXS Type-R
the losi is not ideal for VTA. Can't run low FDRs
Tech Champion
iTrader: (1)
No offense. Well i wanted to originally but now the zero s is out so....
how do you guys run FDRs 5 and below? Losi's smallest spur is 116T, and I just refuse to make an effort to get those layshafts you guys have been talking about.
I can't imagine how much rear bulkhead material I have to grind just to get newer 6200mahs to fit in Oh well, still luv my losi anyway
how do you guys run FDRs 5 and below? Losi's smallest spur is 116T, and I just refuse to make an effort to get those layshafts you guys have been talking about.
I can't imagine how much rear bulkhead material I have to grind just to get newer 6200mahs to fit in Oh well, still luv my losi anyway
Tech Elite
iTrader: (125)
You can get it to work if you have a PRS adapter or one of the new layshafts. I ran 4.0 all the time in 13.5 before boost speedo's were a big deal. I ran 64 pitch spurs though. 112/51 will put you at 4.02 FDR with 64 pitch spurs/pinions.
Tech Adept
You can also help yourself by using the 41T diff pulley on both differentials.
i.e. a 112/51 as previously illustrated will put you at 3.91
i.e. a 112/51 as previously illustrated will put you at 3.91
The type-r is one of the most potent VTA cars out there because of the turn in it has and the short arms. As for the FDR i was able to get to 4.2 w/ stock kevlar 118 and larger pinions. in VTA i've run two back to back 8min heats w/ the same 5600 and still had 20% left in the pack, you must have a huge track to need a 6xxx lipo.
Tech Regular
iTrader: (13)
No offense. Well i wanted to originally but now the zero s is out so....
how do you guys run FDRs 5 and below? Losi's smallest spur is 116T, and I just refuse to make an effort to get those layshafts you guys have been talking about.
I can't imagine how much rear bulkhead material I have to grind just to get newer 6200mahs to fit in Oh well, still luv my losi anyway
how do you guys run FDRs 5 and below? Losi's smallest spur is 116T, and I just refuse to make an effort to get those layshafts you guys have been talking about.
I can't imagine how much rear bulkhead material I have to grind just to get newer 6200mahs to fit in Oh well, still luv my losi anyway
batt
ok so i see a lot of pplz doing diff things w/gearing .. has anyone noticed any effect by using a diff batt ? higher C rating ?
I just got my 6500mah, maxamps, 150c rated batt. itching to try it tommorrow.
I just got my 6500mah, maxamps, 150c rated batt. itching to try it tommorrow.
Tech Champion
iTrader: (1)
The main reason you get the FF layshaft is it spreads the pulleys so they don't hit your lipo. It saves you sanding down pulleys to do the same thing.
quick q...i'm just getting around to put in a ballistic 17.5 motor and the solder tabs hit the bulkhead...is there some motor spacer that you guys are using to get this motor to not hit ? thanks
Tech Elite
iTrader: (74)
Tech Elite
iTrader: (74)
steal lipo tray
Hi guys, jus wondering on the steel lipo tray, does it have a lip ? the lip on the factory tray is too small .... dun wana have to dremel .. hahaha
a pic of the inside would be appreciated.
a pic of the inside would be appreciated.