TC3Racer67

yeah, i've dyed all of my novak equipment.

cHckbOY5

man that BMI chassis is hot ... i like the "4" ont he shock towers

acutts

Anyone got a website to view the BMI chassis?

leekayliang

Where to get those BMI chassis?

wyd

iTrader: (51)

You can go to their website at bmiracing.com. You can go to their website and they have a phone number you can call as well.

acutts

There don't seem to be any pics of the BMI Pro4 chassis on the site?? Anyone got a pic to show?

rayhuang

iTrader: (5)

If you ook back the last two pages of this thread are probabl 10 pics of the BMI car!! Enjoy!!

Heres a pic of the RPM bumper on the car. Again-its not done quite as well as it should be-but it should do the job for a week or so!

Ray

rc-zombies

iTrader: (9)

don't forget.... the 0 deg blocks are available as well....

I've got 2 complete sets coming... 0, 1, 1.5, & 2
along with the new Pro4 stiffer springs:
#6545 14x25x1.5x5.75
#6456 14x25x1.5x5.25

3023430206545,HPI,380YEN,6545 RACING SHOCK SPRING 14*25*1.5MM 5.75 COILS(WHITE),
3023430206546,HPI,380YEN,6546 RACING SHOCK SPRING 14*25*1.5MM 5.5 COILS(YELLOW), 3023430275156,HPI,,800yen,75156 PIVOT BLOCK 0 DEGREES(ALUMINUM/PURPLE)
3023430275158,HPI,,800yen,75158 PRO4 PIVOT BLOCK 1 DEGREES(ALUMINUM/PURPLE)
3023430275159,HPI,,800yen,75159 PRO4 PIVOT BLOCK 1.5 DEGREES(ALUMINUM/PURPLE)
3023430275160,HPI,,800yen,75160 PRO4 PIVOT BLOCK 2 DEGREES(ALUMINUM/PURPLE)

rayhuang

iTrader: (5)

Heres a shot from the bottom.

HOw it needs to be improved is I need to nove it back about 5mm.

Also-its upside down-why? S that I had a flat surface to place on the chassis. IT wont work right-side-up.

Ray

rayhuang

iTrader: (5)

Even as far forward as I have this bumper-the body still fits on over the it. I think I mounted this Parma Alpha body a few mm forward of where I put it on the TC3 and Xray. I'd prefer it back a teeny bit.

Ray

Steve Weiss

So Thad, would you care to give us a play-by-play of what you consider "the best marshalling thing ever"???

wyd

iTrader: (51)

Looks good though. Fits nicely on the car.

wyd

iTrader: (51)

I posted a bunch and so did Ray only a page or two back. Ray had some nice shots and I had a closeups of the front tower, rear tower, and toplate. I'm putting on my new chassis tonight and will post later this evening.

rayhuang

iTrader: (5)

I remember someone asking what electronics will fit in the Pro4.

In this pic is:

Novak GT7 with Cap and diode bridge mounted on chassis under driveshaft.

KO 2143 Servo (pretty big as far as servos go).

KO KR 301F Receiver-again-not exactly small.

AMB Transponder mounted flat on chassis in front of batteries. So no problems fitting standard electronics in this car. The Cap hangs off just a bit-but if I were to run without the center brace-I could slide it way farther in.

rc-zombies

iTrader: (9)

Your car is looking good Ray...

That's the way I have mine set-up as well but with:

HB Hara Twister
Futaba S9451 servo
Futaba H203 HRS

If I want to make more room and install a fan...I use the Futaba S9550 Digital Low Profile servo.