Orion V2
09-19-2005, 03:55 AM
#316
Tech Master
iTrader: (22)
Join Date: Aug 2003
Location: Where there's smoke there's a tyre
Posts: 1,784
Trader Rating: 22 (100%+)
Originally Posted by Rookie Solara
Yes, that is exactly what JOE (from Team Orion) told me before I purchased the Touring version for my Pro 4.......beside soldering the wires on the endbell is a pain, this motor is AWESOME.
09-19-2005, 07:37 AM
#317
Originally Posted by Team-RTR
hey people, when i go full throttle with my V2 motor the motor stutters really badly and then takes off. the comm has just been freshly cut and the motor is in perfect running condition. the ESC is a novak GTX.
09-19-2005, 07:14 PM
#318
the light was on. i found out the problem. i slightly overtightened the cap screws that holds the endbell on and a deformed the ring that the endbell screws onto. i straightened it out again and the motor is fine.
10-31-2005, 01:10 PM
#320
Originally Posted by Deznuts05
Hello,
I recently purchased one of these V2 hoods and I'm not sure how to rebuild it.
Could someone either take pictures of how to rebuild it or explain what steps I need to take?
Thank you,
Rudy
I recently purchased one of these V2 hoods and I'm not sure how to rebuild it.
Could someone either take pictures of how to rebuild it or explain what steps I need to take?
Thank you,
Rudy
Curtis from DC did a write-up on this. Click on the link below, then click "V2 Spring & Brush Replacement"
http://dcmotorsports.net/tips_tricks.html
08-09-2006, 03:22 PM
#322
hi, just get the marc reinhard 12x2 edition.... it is my first brushed mod (got 5.5r brushless) does anyone knows the web, springs and brush type it comes with? what would be the proper range for gearing (technical track), something between, 8.5 and 9? what would be a good start?
thanks a lot,
al
thanks a lot,
al
08-10-2006, 02:06 PM
#323
Originally Posted by rampal
hi, just get the marc reinhard 12x2 edition.... it is my first brushed mod (got 5.5r brushless) does anyone knows the web, springs and brush type it comes with? what would be the proper range for gearing (technical track), something between, 8.5 and 9? what would be a good start?
thanks a lot,
al
thanks a lot,
al
please, thanks!
al
08-10-2006, 03:02 PM
#324
Originally Posted by rampal
hi, just get the marc reinhard 12x2 edition.... it is my first brushed mod (got 5.5r brushless) does anyone knows the web, springs and brush type it comes with? what would be the proper range for gearing (technical track), something between, 8.5 and 9? what would be a good start?
thanks a lot,
al
thanks a lot,
al
For gearing it really depends on the track size. A 8.5 would be good for a tight technincal short track. For a larger track you may want a 8.0 or lower.
08-11-2006, 08:18 PM
#325
I newbie want to buy V2 motor team orion, what the best edition of V2 team orion motor
Last edited by nino_pohan; 08-13-2006 at 05:01 AM.
08-11-2006, 11:11 PM
#327
Im in quite a dilema. I took apart my vantage to give the comm a cut, and when I removed the endbell, one of the copper looking pieces being the tubes where the brushes are inserted fell out. I took the board off of the endbell and tried to slide the copper looking piece back in, but it broke. Is there any way i can get a new piece or do i need a new motor? Or maybe can I just buy an endbell adaption kit?
08-12-2006, 03:13 AM
#328
Tech Master
Yeah those bits are available seperately. I have also just soldered a link accross when i've been desparate at the track. However, you have to be very careful doing this as you can end up with too much there and it'll hit the comm tabs!
08-12-2006, 06:27 AM
#329
What the best team orion V2 motor, Marc edition or Hara edition?
