R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

Reply
 
Thread Tools Search this Thread
Old 09-19-2005, 04:55 AM   #316
Tech Master
 
dontfeelcold's Avatar
 
Join Date: Aug 2003
Location: Where there's smoke there's a tyre
Posts: 1,721
Trader Rating: 21 (100%+)
Default

Quote:
Originally Posted by Rookie Solara
Yes, that is exactly what JOE (from Team Orion) told me before I purchased the Touring version for my Pro 4.......beside soldering the wires on the endbell is a pain, this motor is AWESOME.
the wires are easy to solder on, keeping them on in warm to hot weather is a different story all together, it happens way to easily.
dontfeelcold is offline   Reply With Quote
Old 09-19-2005, 08:37 AM   #317
Tech Initiate
 
Spud_J's Avatar
 
Join Date: Sep 2004
Location: Norwich, UK
Posts: 46
Default

Quote:
Originally Posted by Team-RTR
hey people, when i go full throttle with my V2 motor the motor stutters really badly and then takes off. the comm has just been freshly cut and the motor is in perfect running condition. the ESC is a novak GTX.
Check that the red LED lights up inside when powered up - showing that the capacitors are connected. If not, take off the endbell and check the little copper connectios inside. This is more likely your problem
Spud_J is offline   Reply With Quote
Old 09-19-2005, 08:14 PM   #318
Tech Fanatic
 
Team-RTR's Avatar
 
Join Date: Jan 2004
Location: sydney
Posts: 917
Default

the light was on. i found out the problem. i slightly overtightened the cap screws that holds the endbell on and a deformed the ring that the endbell screws onto. i straightened it out again and the motor is fine.
__________________
SERPENT | NOVAROSSI | XRAY | TEKIN | FUTABA
Team-RTR is offline   Reply With Quote
Old 10-31-2005, 01:48 PM   #319
Tech Fanatic
 
Join Date: Sep 2004
Location: Graduate Hospital
Posts: 966
Trader Rating: 9 (100%+)
Send a message via AIM to Deznuts05
Default

Hello,

I recently purchased one of these V2 hoods and I'm not sure how to rebuild it.

Could someone either take pictures of how to rebuild it or explain what steps I need to take?

Thank you,

Rudy
Deznuts05 is offline   Reply With Quote
Old 10-31-2005, 02:10 PM   #320
Tech Fanatic
 
Arun's Avatar
 
Join Date: Jun 2003
Location: GA
Posts: 753
Default

Quote:
Originally Posted by Deznuts05
Hello,

I recently purchased one of these V2 hoods and I'm not sure how to rebuild it.

Could someone either take pictures of how to rebuild it or explain what steps I need to take?

Thank you,

Rudy
Hey Rudy,

Curtis from DC did a write-up on this. Click on the link below, then click "V2 Spring & Brush Replacement"

http://dcmotorsports.net/tips_tricks.html
__________________
http://nexusracing.com
Arun is offline   Reply With Quote
Old 10-31-2005, 03:05 PM   #321
Tech Fanatic
 
Join Date: Sep 2004
Location: Graduate Hospital
Posts: 966
Trader Rating: 9 (100%+)
Send a message via AIM to Deznuts05
Default

thank you very much
Deznuts05 is offline   Reply With Quote
Old 08-09-2006, 04:22 PM   #322
Tech Addict
 
rampal's Avatar
 
Join Date: Feb 2006
Location: Madrid, Spain
Posts: 563
Trader Rating: 4 (100%+)
Send a message via MSN to rampal
Default

hi, just get the marc reinhard 12x2 edition.... it is my first brushed mod (got 5.5r brushless) does anyone knows the web, springs and brush type it comes with? what would be the proper range for gearing (technical track), something between, 8.5 and 9? what would be a good start?

thanks a lot,
al
__________________
The Blue Armada: Tamiya TRF415MSXX, Tamiya TA05MS, Tamiya/Xenon TA05
Novak Brushless, Orion/Peak LiPo batteries, 5-cell
Sanwa M11 DSSS, KO Propo Servos
rampal is offline   Reply With Quote
Old 08-10-2006, 03:06 PM   #323
Tech Addict
 
rampal's Avatar
 
Join Date: Feb 2006
Location: Madrid, Spain
Posts: 563
Trader Rating: 4 (100%+)
Send a message via MSN to rampal
Default

Quote:
Originally Posted by rampal
hi, just get the marc reinhard 12x2 edition.... it is my first brushed mod (got 5.5r brushless) does anyone knows the web, springs and brush type it comes with? what would be the proper range for gearing (technical track), something between, 8.5 and 9? what would be a good start?

thanks a lot,
al

please, thanks!
al
__________________
The Blue Armada: Tamiya TRF415MSXX, Tamiya TA05MS, Tamiya/Xenon TA05
Novak Brushless, Orion/Peak LiPo batteries, 5-cell
Sanwa M11 DSSS, KO Propo Servos
rampal is offline   Reply With Quote
Old 08-10-2006, 04:02 PM   #324
TLRacing
 
Todd Hodge's Avatar
 
Join Date: Sep 2002
Location: California
Posts: 1,676
Default

Quote:
Originally Posted by rampal
hi, just get the marc reinhard 12x2 edition.... it is my first brushed mod (got 5.5r brushless) does anyone knows the web, springs and brush type it comes with? what would be the proper range for gearing (technical track), something between, 8.5 and 9? what would be a good start?

thanks a lot,
al
4mm web, Enduro brush, and for springs I would say the Revolution MR032 4.3 N/mm (8 coil) (ORI41383).

For gearing it really depends on the track size. A 8.5 would be good for a tight technincal short track. For a larger track you may want a 8.0 or lower.
__________________
Todd Hodge
Category Development Manager for Losi and Team Losi Racing
Losi and Team Losi Racing, brands of Horizon Hobby
Team Losi Racing, Orion, Nitrotane, Spektrum, Imagine It Graphics, Bradley Fine Line Designs, and Lunsford.
Todd Hodge is offline   Reply With Quote
Old 08-11-2006, 09:18 PM   #325
Tech Regular
 
nino_pohan's Avatar
 
Join Date: Nov 2005
Posts: 280
Default

I newbie want to buy V2 motor team orion, what the best edition of V2 team orion motor

Last edited by nino_pohan; 08-13-2006 at 06:01 AM.
nino_pohan is offline   Reply With Quote
Old 08-12-2006, 12:10 AM   #326
Tech Elite
 
BSchorr's Avatar
R/C Tech Elite Subscriber
 
Join Date: Jun 2004
Location: Sioux Falls, SD
Posts: 4,820
Trader Rating: 92 (100%+)
Send a message via AIM to BSchorr Send a message via Yahoo to BSchorr Send a message via Skype™ to BSchorr
Default

Quote:
Originally Posted by nino_pohan
I newbie want to buy V2 motor team orion, it was to many edition. what the best V2 marc ed. , hara ed. or ??? i play TC.
Umm? English and vocabulary sentence structure please?
__________________
Proline ~ Genesis R/C Products ~ First Premier Satellites
BSchorr is offline   Reply With Quote
Old 08-12-2006, 12:11 AM   #327
Tech Master
 
Switch Blade's Avatar
 
Join Date: Jan 2003
Location: The British Invasion
Posts: 1,078
Send a message via AIM to Switch Blade
Default

Im in quite a dilema. I took apart my vantage to give the comm a cut, and when I removed the endbell, one of the copper looking pieces being the tubes where the brushes are inserted fell out. I took the board off of the endbell and tried to slide the copper looking piece back in, but it broke. Is there any way i can get a new piece or do i need a new motor? Or maybe can I just buy an endbell adaption kit?
__________________
College
Switch Blade is offline   Reply With Quote
Old 08-12-2006, 04:13 AM   #328
Tech Master
 
Join Date: Aug 2001
Location: England
Posts: 1,470
Send a message via ICQ to MattW
Default

Yeah those bits are available seperately. I have also just soldered a link accross when i've been desparate at the track. However, you have to be very careful doing this as you can end up with too much there and it'll hit the comm tabs!
MattW is offline   Reply With Quote
Old 08-12-2006, 07:27 AM   #329
Tech Regular
 
nino_pohan's Avatar
 
Join Date: Nov 2005
Posts: 280
Default

What the best team orion V2 motor, Marc edition or Hara edition?
nino_pohan is offline   Reply With Quote
Old 08-12-2006, 03:23 PM   #330
Tech Master
 
Guo Chean's Avatar
 
Join Date: Jan 2005
Location: Indiana, PA15701
Posts: 1,492
Trader Rating: 4 (100%+)
Send a message via ICQ to Guo Chean Send a message via Yahoo to Guo Chean
Default

oscar jansen edition it come with the new alum endbell and new armature
__________________
[FONT=Comic Sans MS][SIZE=3][COLOR=red]|HotBodies|HPI|Full Throttle Motorsports|KO PROPO|DSM|Nosram|JACO|MUCH MORE RACING|Schacht Design Works|[/COLOR][/SIZE][/FONT]
Guo Chean is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
Orion 3200 Lipos. Orion Charger, Orion balancer *new price* Mike Marshall R/C Items: For Sale/Trade 4 08-07-2008 09:26 AM
FS: Orion Advantage Charger w/2 Orion Carbon Edition 3200 Packs smarking1212 R/C Items: For Sale/Trade 4 05-26-2008 02:44 AM
Orion Advantage Charger with 2 lipos orion/peak Rock Racing R/C Items: For Sale/Trade 1 04-21-2008 05:31 PM
Orion advantage carbon edition charger + Orion 3200 spec LiPo $150.00 vintagetamiya R/C Items: For Sale/Trade 9 04-09-2008 05:05 PM
New Orion 1100 micro battert and Orion Mod Elite for Sale Nightbreed R/C Items: For Sale/Trade 0 01-29-2003 02:11 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 10:20 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net