Tekin RS ESC sensored
#2762
Tech Master
--
Last edited by mikky32; 03-06-2009 at 10:35 AM.
#2763
Tech Adept
hey chaps i would like to know what motor settings i should run on my RS with a 17.5 tekin motor gearing to around 44mm rollout, foam on asphalt and locked into a corally rdx phi? is there a feature like launch control
(as found on the lrp Sphere tc spec) ??? if not could i suggest some setting like that programmed in..
(as found on the lrp Sphere tc spec) ??? if not could i suggest some setting like that programmed in..
#2764
Tech Elite
iTrader: (16)
hey chaps i would like to know what motor settings i should run on my RS with a 17.5 tekin motor gearing to around 44mm rollout, foam on asphalt and locked into a corally rdx phi? is there a feature like launch control
(as found on the lrp Sphere tc spec) ??? if not could i suggest some setting like that programmed in..
(as found on the lrp Sphere tc spec) ??? if not could i suggest some setting like that programmed in..
If you run the 1.89 firmware in your RS, then check sensor mode, run the boost to maximum, turn the endbell timing all the way clockwise, rollout around 44-44.5mm.
Watch temps, and gear accordingly for lap time, but those will be close.
#2765
Mikky:
We take every customer seriously regardless of where you're located. However there are a lot of times where we service sent in that has nothing wrong, user error or some other issue that is esc controlled.
I know Jim is not ignoring you. However he is a very busy man and may not be the correct person to be talking to. The normal channel would have been via [email protected] or you could have delt with me [email protected] as I know we've spoke in the past.
We ship to the address we are given. If there's an error with that we cannot be held responsible for those errors.
Please forward me any emails you've gotten so I can see where we are at with your service issue: [email protected]
We take every customer seriously regardless of where you're located. However there are a lot of times where we service sent in that has nothing wrong, user error or some other issue that is esc controlled.
I know Jim is not ignoring you. However he is a very busy man and may not be the correct person to be talking to. The normal channel would have been via [email protected] or you could have delt with me [email protected] as I know we've spoke in the past.
We ship to the address we are given. If there's an error with that we cannot be held responsible for those errors.
Please forward me any emails you've gotten so I can see where we are at with your service issue: [email protected]
#2766
Guest
Hi,
What is the recommended FDR for my tekin 6.5T brushless motor ? I will be using it with a RS PRO in 189.
I was told to gear down, but since I don't know the recommended FDR, I'm stuck.
FYI, this is the track where I'm going to practice
http://www.youtube.com/watch?v=tC6UpXcWKeA
Thanks a lot !
Cédric
What is the recommended FDR for my tekin 6.5T brushless motor ? I will be using it with a RS PRO in 189.
I was told to gear down, but since I don't know the recommended FDR, I'm stuck.
FYI, this is the track where I'm going to practice
http://www.youtube.com/watch?v=tC6UpXcWKeA
Thanks a lot !
Cédric
Last edited by okayplayer; 03-06-2009 at 10:26 AM.
#2767
Tech Master
I removed my earlyer post because i got an explanation from Jim with what the problem was. Sorry for wath is posted.
Someting in the communication went wrong.
Someting in the communication went wrong.
#2768
#2769
Guest
Hi,
What is the recommended FDR for my tekin 6.5T brushless motor ? I will be using it with a RS PRO in 189.
I was told to gear down, but since I don't know the recommended FDR, I'm stuck.
FYI, this is the track where I'm going to practice
http://www.youtube.com/watch?v=tC6UpXcWKeA
Thanks a lot !
Cédric
What is the recommended FDR for my tekin 6.5T brushless motor ? I will be using it with a RS PRO in 189.
I was told to gear down, but since I don't know the recommended FDR, I'm stuck.
FYI, this is the track where I'm going to practice
http://www.youtube.com/watch?v=tC6UpXcWKeA
Thanks a lot !
Cédric
#2770
Tech Elite
iTrader: (16)
Hi,
What is the recommended FDR for my tekin 6.5T brushless motor ? I will be using it with a RS PRO in 189.
I was told to gear down, but since I don't know the recommended FDR, I'm stuck.
FYI, this is the track where I'm going to practice
http://www.youtube.com/watch?v=tC6UpXcWKeA
Thanks a lot !
Cédric
What is the recommended FDR for my tekin 6.5T brushless motor ? I will be using it with a RS PRO in 189.
I was told to gear down, but since I don't know the recommended FDR, I'm stuck.
FYI, this is the track where I'm going to practice
http://www.youtube.com/watch?v=tC6UpXcWKeA
Thanks a lot !
Cédric
Help us to help you... what kind of car are you asking about?
#2771
Guest
Hi,
Sorry, here's some information on my setup that may help you to help me.
Basics & electronics
I (will on monday) run for first time my Xray T2 EU 009, on asphalt (see the youtube video with the track) with rubber tyres (Jaco Green) or RB 4xfront foam tyres (shore 35) with a Mazda 6 bodyshell.
Car is "perfectly" setup with a hudy according to the T2 manual (EU asphalt)
My electronic is : Tekin RS PRO (v189) + Tekin 6.5T (on a 21T pinion for the moment) with a 48 - 84 Spur.
Tekin RS PRO setup:
I have in stock also a 87 spur and ordered a 17 & 19T pinions
According to the manual, here're the FDRs :
Spur 84
17T:8.40
19T:7.52
21T:6.80
Spur 87
17T:8.70
19T:7.78
21T:7.04
Hope that helps,
1/ what is the FDR to go for the 6.5T motor ?
2/ any remarks ?
Cédric
Sorry, here's some information on my setup that may help you to help me.
Basics & electronics
I (will on monday) run for first time my Xray T2 EU 009, on asphalt (see the youtube video with the track) with rubber tyres (Jaco Green) or RB 4xfront foam tyres (shore 35) with a Mazda 6 bodyshell.
Car is "perfectly" setup with a hudy according to the T2 manual (EU asphalt)
My electronic is : Tekin RS PRO (v189) + Tekin 6.5T (on a 21T pinion for the moment) with a 48 - 84 Spur.
Tekin RS PRO setup:
I have in stock also a 87 spur and ordered a 17 & 19T pinions
According to the manual, here're the FDRs :
Spur 84
17T:8.40
19T:7.52
21T:6.80
Spur 87
17T:8.70
19T:7.78
21T:7.04
Hope that helps,
1/ what is the FDR to go for the 6.5T motor ?
2/ any remarks ?
Cédric
Last edited by okayplayer; 03-06-2009 at 01:37 PM.
#2772
Tech Regular
iTrader: (25)
Redline in a crc gen x
Has anyone tried to put a redline in a crc gen x 12? I can't figure out how to get it in there. Novak brushless motors fit. they are slightly shorter and the sensor wire is on the side of the endbell as apposed to the redline where it is at the bottom.
Any help thanks
Dan
Any help thanks
Dan
#2773
Tech Master
#2774
Randy,
On the set ups for RS & 17.5, I noticed that you are using the Throttle pro #3.
Would throttle #5 be better?
What are the differences besides more aggressive?
Thanks and God Bless
On the set ups for RS & 17.5, I noticed that you are using the Throttle pro #3.
Would throttle #5 be better?
What are the differences besides more aggressive?
Thanks and God Bless
#2775
Tech Champion
iTrader: (103)
Need help!! I'm trying to calibrate my KO Helios to my RS speedo. After setting the throttle throw, I get the 1,2,3 lights blinking indicating that my radio signal is lower than expecte. I tried making different adjustments with the same result. I even tried an M8 and still have the same problem. Anyone have a clue as to what would cause this? Thanks.