4LikesScale RC
10-23-2010 | 11:31 AM
#1681
Joined: Mar 2002
Posts: 2,834
From: Singapore
Still working on having some custom 1.9 BL's with a little more offset, done. GREAT if it can have BL rings just like the 1:1?
Thanks, Kupsss!
10-23-2010 | 09:27 PM
#1682
ALMOST BACK
Yup I'm back with a vengeance, I missed a lot the past year or so, I'll try to make up for it with our new project.. We're not officially open yet but we're already working on something special. 
The wife and I will be visiting you soon..I have a wish list on hand. She will be more involved in the shop since I will be occupied naman with something they call day job
. I will still handle the design though. 
The wife and I will be visiting you soon..I have a wish list on hand. She will be more involved in the shop since I will be occupied naman with something they call day job
. I will still handle the design though.
10-24-2010 | 11:21 PM
#1683
Watta comp yesterday! One of the trickiest and hardest courses ever laid out. Death boulders made us team DNF again on the second heat! Sir miles lang ang nakatapos ng reverse course, Fen, MUNTIK NA!, but nice one bro, clear ka sa gate na yun! Ako rin almost, but its hard to climb to the finish with only 3 wheels attached and 10 seconds left!
Thanks again Scaleheads, F48 & Crazy C.
Sana nandun lahat next comp.
Just a few pics of Elpaks' Ninja Honcho (Winner again, congrats!) and madda's rc4wd boyer truggy maiden comp run. (congrats too, siga yung boyer truggy mo bro!).
Sayang I didnt get to take a photo of SirMiles new CC01 bronco, really really nice.
Thanks again Scaleheads, F48 & Crazy C.
Sana nandun lahat next comp.
Just a few pics of Elpaks' Ninja Honcho (Winner again, congrats!) and madda's rc4wd boyer truggy maiden comp run. (congrats too, siga yung boyer truggy mo bro!).
Sayang I didnt get to take a photo of SirMiles new CC01 bronco, really really nice.
10-25-2010 | 09:30 PM
#1685
Watta comp yesterday! One of the trickiest and hardest courses ever laid out. Death boulders made us team DNF again on the second heat! Sir miles lang ang nakatapos ng reverse course, Fen, MUNTIK NA!, but nice one bro, clear ka sa gate na yun! Ako rin almost, but its hard to climb to the finish with only 3 wheels attached and 10 seconds left!
Thanks again Scaleheads, F48 & Crazy C.
Sana nandun lahat next comp.
Thanks again Scaleheads, F48 & Crazy C.
Sana nandun lahat next comp.
sayang talaga bro! heat na pangbawi, nawala pa, naubos oras! that's the hardest course bro, pang 2.2 rock crawler ang design,
pag may taga TTC or MSD na sumali satin, malamang, talo ng team DNF yan!madda/mix/miles/elpaks: thanks sirs! buti binigyan nyo ko ng pwesto na pang 5th
f48/crazy crawler: thanks guys!
SCALEHEADS: last 3comps nalang po mga bowsings! see you on next event!
10-26-2010 | 10:23 PM
#1691
Same concern Madda, I used grease and noise went down drastically but only for a few runs. Subukan mo yun silicon oil na ginagamit sa gearbox ng airsoft halos parehas kasi pitch nun sa gearbox natin ala kasi ako mabili dito.
Tingin ko we can make R2 oil sealed havent observed it fully yet. Pero tingin ko its sealed naman we only need to plug the unused 3mm screw holes with set screws. Then use a very thick oil (100wt+) its thin enough to get in between gears and thin enough to settle down by gravity for another cycle but thick enough not to or minimal leak/seep out between bearing and output shaft even w/o o-rings/seals. The next thick silicon oil I can think of is Tire Black ala lang ako time mag experiment sobra busy sa work lately
10-26-2010 | 11:07 PM
#1692
Joined: Mar 2002
Posts: 2,834
From: Singapore
Same concern Madda, I used grease and noise went down drastically but only for a few runs. Subukan mo yun silicon oil na ginagamit sa gearbox ng airsoft halos parehas kasi pitch nun sa gearbox natin ala kasi ako mabili dito.
Tingin ko we can make R2 oil sealed havent observed it fully yet. Pero tingin ko its sealed naman we only need to plug the unused 3mm screw holes with set screws. Then use a very thick oil (100wt+) its thin enough to get in between gears and thin enough to settle down by gravity for another cycle but thick enough not to or minimal leak/seep out between bearing and output shaft even w/o o-rings/seals. The next thick silicon oil I can think of is Tire Black ala lang ako time mag experiment sobra busy sa work lately
Tingin ko we can make R2 oil sealed havent observed it fully yet. Pero tingin ko its sealed naman we only need to plug the unused 3mm screw holes with set screws. Then use a very thick oil (100wt+) its thin enough to get in between gears and thin enough to settle down by gravity for another cycle but thick enough not to or minimal leak/seep out between bearing and output shaft even w/o o-rings/seals. The next thick silicon oil I can think of is Tire Black ala lang ako time mag experiment sobra busy sa work lately
10-27-2010 | 01:06 AM
#1693
siggy: Siga tumakbo yung Boyer chief. I love the torque and the overall power to weight ratio (using 27T brushed). I have to work on the steering though. Bitin lumiko eh.
edwin: Sa umpisa lang nakaka-ilang yung tunog pero masasanay ka rin. Akala ko nga may masisira but it looks very durable and sturdy. Tumagal ng 2 hours straight trailing and hardcore comp.
edwin: Sa umpisa lang nakaka-ilang yung tunog pero masasanay ka rin. Akala ko nga may masisira but it looks very durable and sturdy. Tumagal ng 2 hours straight trailing and hardcore comp.
10-27-2010 | 02:52 AM
#1694
Joined: Mar 2002
Posts: 2,834
From: Singapore
Naguusap kami ngayon ni Boyer at nagpapagawa ako sa kanya ng iang chassis na may full roll bar at full exo-cage. Sarado na kami sa presyo, ang pinag-dedesisyonan na lang ay kung anong body at detalye ny disenyo. Hahanap hanap ako ng matutularan at eto pa lang ang nakita ko ...
Tunkol sa motor, alam mo para sa scale eh nagiging paborito ko yun 27T Brushed ng SCX, pang harabas. Parang swak na swak sa sa tranny ng SCX.