Where do you get the J-Dub Hub

http://www.rctech.net/forum/nitro-of...-fab-shop.html

PM him. He will take care of ya.

I installed Answer RC bearings before last race meet, which I really rate, and yet these are on their way out, and would of been max one hour running.

Funds are a bit short at mo, but once available, i'll be going to a modded hub

No its not. if your replacing it every 10 min you have issues, the stock bearing lasted longer then that.

ive ran 64 min + lots of practice on a set of avids and there great, maintain them and you shouldnt have issues, yes the mod MAY prolong them but if im gettin a gallon+ outta 1$ bearings im fine with that. they still feel brand new

Yea but it takes you 32 min for 1 lap. I maintain my stuff better than most and the stock hubs and bearings SUCK!!! When you get a little faster and more consistent you will understand

is that why i can stick with you until i crash? hmmm seems like im fast enough. pros are only running 42. im running 47. not bad considering i started racing in sept, how long have you been racing?

now i do agree i need to
be more consistent but these numbers arnt bad, also this is my second race with this truck

Thats Funny only drove until the second time I lapped you and then Todd J drove the last 6 minutes

im only one lap behind you??? and btw if u look, my fourth lap in my fourth lap didnt get counted the first time around. i went inside the pipes and came out past the loop and didnt get counted

You run 51 second lap times look at it moron your fastest lap was a high 48 almost 49 the rest are in the 50's but we can place a wager anytime you want. and at the end I dont want any

and again, how long have you been racing? i never said i was faster then you. your a good racer, but you dont have to act like your the best when your not

Never have acted like I was the best! I learn everytime Im out there. I just know who to listen to and who shouldnt be giving out any advice, oh yea and racing the last 2 years off and on.

well many people have thanked me for advice. if i dont know what im talking about i do not give advice, as far as bearings go MY PERSONAL experience has been good in the 8t2.0, i am thinking about grabing the kh rear hub just for insurance but i dont think its needed. others it may not but hey thats racing. Hopefully your at the track this weekend, your fun to race against, and i agree with you i learn every time i go out to. one thing i wanna ad is its hard passing you because we have the same lines everywhere on that track

You cant pass me when your on your lid

HA HA, hey i could of put you on your lid a couple times passing you but i stopped so you could straighten out im thinking about painting the bottom of the chassis to match my lid LOL

i've been running the same set of bearings untouched since i modded the hubs that came on the car. i've done upwards of 15 hours racing on the same rear bearings. so if your content to change them every second meeting then its your wasted money.
My modded om my 8T saw over 6 months of racing without a bearing change.


I dont want to sound like a rude prick, but im fair sick of it being called the J-DUB Hub Mod when it was my idea. It was me who found J-DUB to do it for you in the USA so i didnt have to ship them half way around the world.
I came up with this design back in April last year. So far i've had my idea ripped off by 2 mainstream companies (KH and Integy) who wouldn't even know who to thank for the money they have made off someone elses idea. J-DUB does a great job on the mod and i hold no grudge on him doing the work but even he will tell you its not his mod. I just didnt want people to have to pay for shipping from Australia

Losi made a massive mistake with the release of the 8T 2.0 with the 14mm bearing, and it took the commen racer to fix the problem. Not a pro or an engineer on a 6 figure pay packet.
The big companies have no problems stealing your ideas to line there own pockets but have massive problems giving credit where credit is due.
next time ill copyright the idea and charge them for it.


Anyway continue to contact J-DUB if you live in the states. He does an awsome job.
If you live in the Southern Hemisphere and you need the hubs send me a PM
Dont be tempted to waste your money on the aluminium hubs when the plastic ones will last forever.