Community
Wiki Posts
Search

Battery issues

Thread Tools
 
Search this Thread
 
Old 04-17-2022 | 06:10 AM
  #1  
Thread Starter
Tech Rookie
 
Joined: Apr 2022
Posts: 1
Default Battery issues

I purchased a brand new GTL energy super power 4000mah 7.2v NI-MH. I have installed it in my MF01X chassis with TBLE-04S esc and tamiya torque tuned motor. I’m only getting around 5 mins run time out of the car. I have used it and fully recharged the battery several times to attempt to recondition the battery. Do you think the battery is no good? Any help would be appreciated. The recharge is only taking about 10mins as the light goes off on the charger when it is full. This makes me think the battery is not getting a full charge. Also not getting any heat from the battery during charge.
kirito34 is offline  
Old 04-17-2022 | 06:46 AM
  #2  
Tech Adept
iTrader: (1)
 
Joined: Mar 2021
Posts: 185
From: Melbourne, Australia
Default

Originally Posted by kirito34
I purchased a brand new GTL energy super power 4000mah 7.2v NI-MH. I have installed it in my MF01X chassis with TBLE-04S esc and tamiya torque tuned motor. I’m only getting around 5 mins run time out of the car. I have used it and fully recharged the battery several times to attempt to recondition the battery. Do you think the battery is no good? Any help would be appreciated. The recharge is only taking about 10mins as the light goes off on the charger when it is full. This makes me think the battery is not getting a full charge. Also not getting any heat from the battery during charge.
It's more likely the battery is not fully charging. Can you perhaps try a different charger. Maybe take it to the shop to charge.
Team Steve is offline  
Old 04-17-2022 | 09:29 AM
  #3  
Tech Master
iTrader: (6)
 
Joined: Dec 2015
Posts: 1,418
From: San Jose CA
Default

What is the voltage at the end of the charge? - use a voltmeter to check. It should be about 8.4 volts.
belewis01 is offline  
Old 04-17-2022 | 10:56 AM
  #4  
sosidge's Avatar
Tech Elite
 
Joined: Dec 2001
Posts: 4,650
From: Bristol, UK
Default

Also a NiMH will be hand warm once charged.

You are probably experiencing a "false peak" where the battery voltage drops and the charger thinks it is full when it isn't. If the battery isn't warm to the touch, just start the charge again.
sosidge is offline  
Old 04-17-2022 | 04:34 PM
  #5  
gigaplex's Avatar
Tech Champion
iTrader: (2)
 
Joined: Dec 2015
Posts: 7,766
From: Melbourne, VIC
Default

Could also be lipo voltage cutoff in the ESC preventing you from getting all the charge out of the NiMH battery. Turn that off in the ESC if it's enabled.
gigaplex is offline  
Old 04-17-2022 | 06:15 PM
  #6  
OVA's Avatar
OVA
Tech Lord
iTrader: (91)
 
Joined: Dec 2002
Posts: 10,514
From: WASHINGTON
Default

Originally Posted by belewis01
What is the voltage at the end of the charge? - use a voltmeter to check. It should be about 8.4 volts.
for lipo yes not NI-HM..normally greater than 9.V at full chr
OVA is offline  
Old 04-21-2022 | 06:57 PM
  #7  
GerryH's Avatar
Tech Fanatic
iTrader: (29)
 
Joined: Nov 2009
Posts: 978
Default

First check that the ESC is in Lo voltage cutoff mode. The instructions can be found here: https://www.tamiyausa.com/media/file...-1207-ad8e.pdf

When the ESC is turned on, you should get a short beep. Lipo mode is a long beep. But if you don't know the difference between short and long, you won't be able to tell until you toggle between them.

If that doesn't work...You didn't mention what charger you're using and what settings you were using to charge the battery. I've never driven that Tamiya model before, but based on similar Tamiya brushed motor models, you should probably get ~20 minutes.
GerryH is offline  
Old 04-21-2022 | 07:47 PM
  #8  
Tech Champion
iTrader: (292)
 
Joined: Sep 2009
Posts: 5,368
From: Central Wisconsin USA
Default

Bad cell or more than one in the pack itself.
Andy Koback is online now  
Old 04-21-2022 | 08:39 PM
  #9  
the rc guy's Avatar
Tech Elite
 
Joined: Aug 2016
Posts: 3,433
From: Detroit
Default

id check every cell in battery 10 min tells me either a bad cell or charger is not working correctly..try to condition battery correctly that charge it at lowest rate your charger has under .5 amps...
the rc guy is offline  
Old 04-21-2022 | 10:39 PM
  #10  
Geezatec's Avatar
Tech Master
 
Joined: Oct 2007
Posts: 1,742
Default

What charger you useing?
Geezatec is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.