RC10B4.1 FT/WC
Tech Master
iTrader: (26)
Joined: Sep 2011
Posts: 1,412
I had some mad glitching problems last night. I am running a tekin rs with a glitch buster cap and futaba 4pl. Any other suggestions that might cause this glitch? I suspect it is my Hobbypartz Solar servo. Does that make sense? I have a Savox I can throw in.
Joined: Mar 2008
Posts: 5,719
From: At dirt tracks in Michigan!
It doesn't hurt to swap electronics in trying to isolate the problem. Definitely try the savox.
Adding a cap was only a temp fix in my case. A BEC will fix the problem, but I didn't care for the setup. ymmv
Tech Master
iTrader: (26)
Joined: Sep 2011
Posts: 1,412
I dont mind adding a BEC if it is necessary. I'll try swapping in the savox servo first. I had been planning to do that anyway.
I a weird issue with a Tekin RS Pro where it turns the Rx on and has power but shows no lights, and I have hot wired and mapped it multiple times, soldered and resoldered connections still nothing but the servo works just fine, but the servo will stutter for a short period on and off? Any help out there?
Joined: Mar 2008
Posts: 5,719
From: At dirt tracks in Michigan!
I a weird issue with a Tekin RS Pro where it turns the Rx on and has power but shows no lights, and I have hot wired and mapped it multiple times, soldered and resoldered connections still nothing but the servo works just fine, but the servo will stutter for a short period on and off? Any help out there?
after connecting the battery the RX will turn on and servo will work but no lights on the Rs Pro and no power to the engine, have checked and rechecked connections , I have remapped with hotwire checked voltage, changed and removed sensor wire no difference any ideas? Thank you for the help!
I had a scre that fell out but I threadlocked it end. And took the other screw out and did the same and my shocks are good I checked them and put callipers on them after I did ride height and they are fine. I may need to check myh hinge pins and I will when I get off work or go on lunch today man thanks and ill let u know what the prob was when I pin point it bro and thanks again
Example see how Kdub interacts with the forum.. he doesnt have to.. but he does... not only does it help people on here but it makes u think to try avid products..right??
But ya is ur servo centering back??
I yet have broken a servo horn "knock on wood". same with the rc8.2 thers nothing wrong with the plastic.. actually something to think about is haveing the right gemoetrey.. make sure if you do go with a alum horn that it doesnt change the height,or other setting from stock... Also dont get be suprised or shock that u break a servo cause now it can happen cause now there is no more flex area at all all the stress is on the servo gears.. specially if u have a servo that has all metal gears except 1 plastic, alot of them do.. think about it..
Throttle would cut. Or my servo would stick turning and i would go in a circle. Sometimes it was just laggy. I had about 5-6 glitches in a 6 min race. It happened first and second race and then the third race of the night it was fine. Not sure what the deal is. I tried 2 different glitch buster caps one spektrum and a racers edge. I use the same setup on my other cars and they did not have a problem. While in the pits I left my buggy on with the hood off and noticed the green light on the futaba reciever would go RED and then my Tekin would restart itself, then the light goes green again. I suspect this is what it was doing while i was racing.
I dont mind adding a BEC if it is necessary. I'll try swapping in the savox servo first. I had been planning to do that anyway.
I dont mind adding a BEC if it is necessary. I'll try swapping in the savox servo first. I had been planning to do that anyway.
Joined: Mar 2008
Posts: 5,719
From: At dirt tracks in Michigan!
after connecting the battery the RX will turn on and servo will work but no lights on the Rs Pro and no power to the engine, have checked and rechecked connections , I have remapped with hotwire checked voltage, changed and removed sensor wire no difference any ideas? Thank you for the help!
Tech Addict
iTrader: (9)
Joined: Apr 2009
Posts: 711
I a weird issue with a Tekin RS Pro where it turns the Rx on and has power but shows no lights, and I have hot wired and mapped it multiple times, soldered and resoldered connections still nothing but the servo works just fine, but the servo will stutter for a short period on and off? Any help out there?
I've trying to figure out the best deal. I bought a B4.1 as a rtr. Since then I've upgraded the front brace, Avid rack, turn buckles, ball cups, battery strap, and ball diff. To get it closer to a Worlds, I still need a longer chassis, shocks and hubs. Would I b better off just buying a Worlds for 250 and sell mine or keep upgrading? Thx



