R/C Tech Forums

Go Back  R/C Tech Forums > General Forums > Electric Off-Road
RC10B4.1 FT/WC >

RC10B4.1 FT/WC

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

RC10B4.1 FT/WC

Thread Tools
 
Search this Thread
 
Old 05-20-2012 | 05:56 PM
  #14971  
1Fastpede's Avatar
1Fastpede
Tech Master
iTrader: (53)
 
Joined: Aug 2010
Posts: 1,757
From: McKinney,TX
Default
yes.
1Fastpede is offline  
Reply
Old 05-20-2012 | 06:06 PM
  #14972  
nhraman
Tech Addict
iTrader: (18)
 
Joined: Sep 2011
Posts: 560
From: Muskegon, MI
Default
Originally Posted by bilster44
28 or 29/72 should be just fine with the 13.5.
This gear combo was money today!! (29/72) Motor temp was at 140 after a 5 minute run plus a couple hot laps. Thanks again!!
nhraman is offline  
Reply
Old 05-20-2012 | 06:11 PM
  #14973  
chancejeff
Tech Adept
iTrader: (1)
 
Joined: Dec 2011
Posts: 198
From: Hesperia, Ca
Default
Originally Posted by zipperfoot
I know its the wire because the same thing happened to me. It would spin fine with throttle holding it off the ground but as soon as i placed it on the ground it would cog. Another pro driver said it was the cable. So i checked it and found it had come loose. The same thing then happened to a buddy but his wire was bad. It looked fine, no damage, but with a new wire it ran fine. There is only one way to plug in the connector. Make sure you didnt force it in the wrong way. Why this happens, no idea.
It was the sensor wire it just wasn't plugged in enough on the esc. Thankyou and to think I thought it wasn't plugged in on the motor enough the whole night it turned out to be the opposite side that wasnt.
chancejeff is offline  
Reply
Old 05-20-2012 | 06:29 PM
  #14974  
Wildcat1971's Avatar
Wildcat1971
Thread Starter
Tech Prophet
iTrader: (84)
 
Joined: Apr 2012
Posts: 17,389
From: Arizona
Default
someone game me a pair of new alum b4 hubs the are .5 (each I assume). I was thinking of putting these on my buggy. I currently have the stock ones that come with the b4/sc10/t4. The plastic ones. They are 0 degree? And what would the .5 hubs do to my setup? more rear bite?
Wildcat1971 is offline  
Reply
Old 05-20-2012 | 06:36 PM
  #14975  
Motofan747's Avatar
Motofan747
Tech Addict
iTrader: (4)
 
Joined: Mar 2011
Posts: 561
Default
Originally Posted by elex300
In order to use the BB springs I need the traxxas collars and 22 cups correct? I know other companies make these but in general this will work?
Yes they will work
Motofan747 is offline  
Reply
Old 05-20-2012 | 06:47 PM
  #14976  
madweazl's Avatar
madweazl
Tech Elite
iTrader: (12)
 
Joined: Oct 2002
Posts: 2,651
From: Nomad
Default
Originally Posted by elex300
In order to use the BB springs I need the traxxas collars and 22 cups correct? I know other companies make these but in general this will work?
The Traxxas lowers work fine and come with the uppers.
madweazl is offline  
Reply
Old 05-20-2012 | 06:52 PM
  #14977  
goin2drt
Tech Elite
iTrader: (77)
 
Joined: Jun 2010
Posts: 2,167
From: Southern California
Default
I bought a used B4.1 WC edition. Can someone give me all the part numbers to re-do the diff. I am confused as I think it is different than a normal B4, correct?
goin2drt is offline  
Reply
Old 05-20-2012 | 07:13 PM
  #14978  
easy e's Avatar
easy e
Tech Master
iTrader: (29)
 
Joined: Sep 2001
Posts: 1,153
From: Shreveport, LA
Default
http://www.rctech.net/forum/r-c-item...ront-rear.html
easy e is offline  
Reply
Old 05-20-2012 | 07:37 PM
  #14979  
carver gt's Avatar
carver gt
Tech Addict
iTrader: (45)
 
Joined: Jul 2009
Posts: 686
From: SoCal
Default
Originally Posted by goin2drt
I bought a used B4.1 WC edition. Can someone give me all the part numbers to re-do the diff. I am confused as I think it is different than a normal B4, correct?
The part numbers should be on the back pages of your instruction manual.
carver gt is offline  
Reply
Old 05-20-2012 | 08:04 PM
  #14980  
RC*PHREAK's Avatar
RC*PHREAK
Tech Champion
iTrader: (147)
 
Joined: Dec 2010
Posts: 5,404
Default
34/72 a decent start point for 17.5 blinky?
RC*PHREAK is offline  
Reply
Old 05-20-2012 | 08:22 PM
  #14981  
mxracer458's Avatar
mxracer458
Tech Elite
iTrader: (47)
 
Joined: Mar 2007
Posts: 3,983
From: so cal
Default
Originally Posted by RC*PHREAK
34/72 a decent start point for 17.5 blinky?
I run 72/31 on indoor clay
mxracer458 is offline  
Reply
Old 05-20-2012 | 08:33 PM
  #14982  
goin2drt
Tech Elite
iTrader: (77)
 
Joined: Jun 2010
Posts: 2,167
From: Southern California
Default
Originally Posted by carver gt
The part numbers should be on the back pages of your instruction manual.
My manual is t4.1/b4.1 NOT WC version which I think are different part numbers.
goin2drt is offline  
Reply
Old 05-20-2012 | 08:35 PM
  #14983  
T-BirdJunkie's Avatar
T-BirdJunkie
Tech Elite
iTrader: (10)
 
Joined: Nov 2004
Posts: 2,974
From: Norwood, OH...and CCRCR and The OhioRCFactory
Default
The T/B4.1 FT uses the same exact diff as the WC.
T-BirdJunkie is offline  
Reply
Old 05-20-2012 | 08:38 PM
  #14984  
goin2drt
Tech Elite
iTrader: (77)
 
Joined: Jun 2010
Posts: 2,167
From: Southern California
Default
Originally Posted by T-BirdJunkie
The T/B4.1 FT uses the same exact diff as the WC.
Thanks
goin2drt is offline  
Reply
Old 05-20-2012 | 08:39 PM
  #14985  
socalrcer's Avatar
socalrcer
Tech Adept
 
Joined: Dec 2010
Posts: 111
From: WCRC
Default
Originally Posted by goin2drt
My manual is t4.1/b4.1 NOT WC version which I think are different part numbers.
As long as your manual shows the Ball Diff, it is the same.
socalrcer is offline  
Reply



Advanced Search

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.