R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
 
Search: Posts Made By: Rcracing01
Showing results 1 to 25 of 103
Search took 0.03 seconds.
04-01-2019, 08:15 AM
Replies: 3
Views: 648
Posted By Rcracing01

T4

Both sold.

Thank you
04-01-2019, 07:51 AM
Replies: 3
Views: 648
Posted By Rcracing01

T4

Both sold pending payment.
03-31-2019, 02:00 PM
Replies: 3
Views: 648
Posted By Rcracing01

Xray T4

The one with upgrades is sold
03-31-2019, 08:46 AM
Replies: 3
Views: 648
Posted By Rcracing01

2017 Xray T4

https://cimg9.ibsrv.net/gimg/www.rctech.net-vbulletin/1500x2000/a13ebad3_5b14_4636_aa2a_7189258e772d_209c7a8ff66d1ee95f1f921ddca7c5abb8b6b0b9.jpeg...
08-30-2018, 04:47 AM
Replies: 4
Views: 1,307
Posted By Rcracing01

Sensor alignment

Hello all,

I have a trinity monster 13.5 with a very accurate sensor board +1 0 +1 but when I put the board on another monster 13.5 it reads way off. I tried it back on the original and it’s...
07-29-2018, 05:37 AM
Replies: 3
Views: 629
Posted By Rcracing01

Battery mah for super stock

Looking at buying new batteries for super stock TC. Would it be better to have higher mah or lower. I am 25g underweight so the additional 20g for the higher mah won’t matter

1) 7.6v 100c 6000mah...
04-09-2018, 04:06 PM
Replies: 8
Views: 1,398
Posted By Rcracing01

Ok thank you for the replies. I have seen the...

Ok thank you for the replies. I have seen the Yeah racing but did not know T works makes them too. I will check them out. Thanks again
04-09-2018, 04:04 PM
Replies: 8
Views: 1,398
Posted By Rcracing01

they wear and also find if you smack the wall...

they wear and also find if you smack the wall hard the cup inside could break.
04-07-2018, 10:44 AM
Replies: 8
Views: 1,398
Posted By Rcracing01

Xray T4 driveshafts

Has anyone tried other manufactures front drive shafts on an Xray T4?
Looking for a lower cost option that is decent.


Thank you
12-19-2017, 06:30 AM
Replies: 1
Views: 585
Posted By Rcracing01

4PLS dropdown

Hello all,

Does any company make a drop down for a 4PLS?
12-10-2017, 07:17 PM
Replies: 5
Views: 661
Posted By Rcracing01

Charging at 6amps

Charging at 6amps
12-10-2017, 05:20 PM
Replies: 5
Views: 661
Posted By Rcracing01

Temp

I got the charger from a fellow racer and he did use it to discharge. But this error is happening on CH1 and not on CH2...
12-10-2017, 10:59 AM
Replies: 5
Views: 661
Posted By Rcracing01

Icharger 308duo exceed safe temp range

Hello all,

Icharger 308duo error msg exceed safe temp range. I don’t even have a temp sensor plugged in.

Any thoughts?
12-09-2017, 08:22 PM
Replies: 9
Views: 8,223
Posted By Rcracing01

Good to hear because I was leaning to the 4PLS...

Good to hear because I was leaning to the 4PLS new or a 4PX used.

Thank you for the feedback
12-09-2017, 04:25 AM
Replies: 9
Views: 8,223
Posted By Rcracing01

4PLS vs 4PV vs 4PX

Hello all,

Trying to determine which is the best bang for your buck. Clearly the PX has the most options but I don’t think I would use all in TC racing.

Any thoughts on comparison?
12-06-2017, 05:44 AM
Replies: 4
Views: 810
Posted By Rcracing01

Even when they are discharging every race it is...

Even when they are discharging every race it is at 40amps
12-06-2017, 05:08 AM
Replies: 4
Views: 810
Posted By Rcracing01

Discharging 2S

Hello all,

Very few racers at my local track discharge in the pits however, a bunch discharge/condition there batteries at home.

Is there an advantage to discharging every race or would every...
11-24-2017, 07:52 PM
Replies: 9
Views: 895
Posted By Rcracing01

Ohhhh

Ohhhh
11-24-2017, 03:22 PM
Replies: 6
Views: 817
Posted By Rcracing01

Great thank you

Great thank you
11-24-2017, 01:07 PM
Replies: 9
Views: 895
Posted By Rcracing01

Yup the Fluke handles that. Thank you

Yup the Fluke handles that. Thank you
11-24-2017, 01:06 PM
Replies: 9
Views: 895
Posted By Rcracing01

Perfect! Thank you

Perfect! Thank you
11-24-2017, 03:45 AM
Replies: 9
Views: 895
Posted By Rcracing01

Thank you Would you happen to know the ohm...

Thank you
Would you happen to know the ohm range it would need to measure within. The Fluke 1507 is showing Resistance: 0.01 Ω to 20.00 kΩ
I check the
11-24-2017, 03:42 AM
Replies: 6
Views: 817
Posted By Rcracing01

Onroad TC

Hello all,

Will any Florida tracks have onroad (carpart or ashphalt) racing on Dec 23-24 or 30-31?

Thank you
11-23-2017, 08:43 PM
Replies: 9
Views: 895
Posted By Rcracing01

Stator checker

Hello all,

Aside from RMS is there any other companies have a resistance meter for stators?
11-13-2017, 05:04 AM
Replies: 911
Views: 300,635
Posted By Rcracing01

I'll try alittle less oil and cleaning the screw...

I'll try alittle less oil and cleaning the screw channels. Thank you much appreciated
Showing results 1 to 25 of 103
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.